66575776891 Kenmore Range - Instructions

took 2 screws out of bottom plate in the oven and lifted it out. removed 2 screw on the flame deflector and took it out. Took 2 screws out of old ignitor and unplugged it. Installed new ignitor tested oven put it back together. took about 30 min. screw driver only

I use the table knife to slide the side of the stove to open the top. then I traced one of the wire to where it was hooked up and remove it and replaced it. I did them one by one.

Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.

Unplug the electrical cord. Remove all the grates and burner caps. Remove the two philips-head screws on each burner. Slide the plastic putty knife under the cooktop in the front to locate two clips. Push in to disengage clips and lift cooktop up in front. Disengage cooktop from the rear of the range. Remove the bad igniter from the burner head and replace with the new, Disconnect the wire from the spark module and install the new wire. Replace the cooktop by securing the rear first and then lowering into place until the clips engage. Replace the philips screws on the burners and the caps and grates. Plug the range back in and you are done.

We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

Put the bottom of the glass in first then put the top half into the brackets in the door handle. Holding it in place with your extra set of hands tighten it down with the two screws from inside the oven door into the back of the handle. The door will be open a lot so be extra careful not to let the door close onto your hands or fingers. Also remember patience is a virtue.

The brief comments on how to with the order was most helpful, no problems replacing frame. Quality is good I thought the price was very high for the parts, considering plastic and metal pieces, but then again compared to new stove reasonable. Remove pieces replace back in order removed.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

We removed with a screwdriver the two main screws that held the bottom of the oven in place and removed the bottom oven piece; then we removed the two nuts with a socket wrench that held the element in place. We then discovered that the element wire did not completely egress to the point of being able to disconnect from within the oven, so we removed the storage drawer below the oven and that provided access to disconnect the element wire and reconnect the new element wire and then reverse the steps to install the new element, which worked fine upon first use and continues to work fine.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Oven is gas. Burners on top OK, broiler in oven OK. Removed oven bottom plate and heat deflector. Carborundum igniter would not glow. Ordered new igniter from Partselect.com. With new igniter in hand I unplugged the oven from house power, removed the bottom drawer for access to the igniter connector, and disconnected it. Removed the bad igniter and replaced with new igniter...easy! Plugged in oven to house power and tested new igniter by turning on oven. GOOD!! Reassemmbled oven interior. Wife again happy.

Had to remove the bottom oven shelf and the broiler drawer. Disconnected the wiring pigtail theought the broiler opening and pulled the gas pipe from the baking oven. Reomved the two screws connecting the ignitor from the pipe. Connected the new ignitor and threaded the wiring pigtail back down the the opening in the baking oven. Connected the wiring harness up inside the broiler and put the drawer back in. Re-installed the bottom shelf in the baking oven and tested. Worked perfectly. Back to cooking. :-)

The video was very helpful and my wife did it..thanks….

Was super easy even I could do it. Wish I would have done it 2 years ago when my husband broke it. Just used a Phillips screwdriver. Very easy!