79095731892 Kenmore Range - Instructions

Remove old element by removing two screws on back wall of oven, pull attached wires out about 6" and disconnect. Reverse to install, very easy. Of course the oven door makes it harder to get at things, but it all worked out. Partselect was the only place I could find the element since the stove is 18 years old. I love keeping appliances going as long as possible.

Pulled out the stove, removed the screws that held on the back panel, took out the 2 screws that held in the element and disconnected the wires and put the new one in. I put the screw back in and was finished!

Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens

order pcs fit perfect.

My husband opened the oven door.He removed the metal strip at the top just under where the knobs are.I held the top of the stove up while he unscrewed the 2 screws on either side of where the knob goes and he unplugged the connectors on the switch assembly one at a time a reconnected the new ones. We slid the post through the hole and lined up the two holes put the screws back in. Walah. I cont. holding up stove he got a socket to unscrew the strip holding the back elements in place. He undid just the one side used pliers to squeeze clamp together pushed the little post through the slot....unplugged the connectors keeping track of them. He used a screwdriver to unscrew clamps to screw them onto the new element at the same number as he took them off the old element. We popped the new element back in hooking up all connectors poked the little clamp posts through the holes attached the screw that is the strip holding elements in place. We closed the stovetop We lined the metal strip up at top of oven door underneath the knobs and put the 4 screws back in and closed the door. Done. I would say it took maybe 30 min.if that. Works like a champ.

i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.

Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.

i had to remove all the broken glass then removed the metal that was holding the glass. set the new glass in the metal strips and screwed it back togethr. i also had to remove the frame from the door in order to get to the inside glass. then i had to put the door back together.

Overlay replacement is easy; 1st remove two screws that hold panel to top of stove (philips screwdriver) and lift up off of lip at very top, 2nd remove two screws that hold control to panel (nutdriver or square drive screwdriver), 3rd peel old overlay from control panel face (make sure you get any & all little bits so new overlay sits flush), 4th peel backing from overlay and position over control panel (peel protective film from face of overlay as well), 5th reposition control panel and reinstall two screws removed in step two above, lastly reposition top panel on stove and reinstall the two screws removed in step one above.
Drawer glide just snaps into place on the lower rear corners of drawer, then you slide drawer back into place.

The repair was fairly easy. The oven door was attached to a spring arm that had one screw holding each arm to the door. Once off, the outside set of screws were removed and saved in a small dish. Each section had 6-10 screws, to it's best to keep each set separate from each other. Each of the three layers (of the door) came apart easily by removing the screws for each section. The inside (broken glass) lifted out, was replaced, and the sequence was repeated in reverse. During the reassembly I was able to clean the other layers of glass that had gotten build-up on them over the years. Total time start to finish was about 30 minutes. Only tool required was a screw driver! Probably saved 100+ dollars!

Slide out the old; slide in the new!

Very important first step: Turn off the circuit breaker for the range or disconnect the power cord.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil element. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.

I must say that I am very pleased with speed of your part delivery, I have to ad that the first part I received was defetive, the inner element was open and therefore it was not working, I called back and a very curteous person took care of the problem, I got a replacement part 2 days later and now all is OK.
Very good service indeed,
Thank you.

I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!

It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!