91195061690 Kenmore Range - Instructions

I removed the 2 nuts and pulled the element out until I reached the disconnect and unhooked the elements from the wire. Replaced the new one in reverse order. It was great finding the part here after Sears said they no longer made the part.

shut power off to range, took 2 screws out, took 2 snap on clips off old element. put snap on clips on new element, put 2 screws back in, and turned breaker on.

Turned off the breaker to the stove, removed oven racks, used small pair of plyers to remove bolts (2) holding defective element in place. Pulled (2) wires that had a snap connection apart. Old element was not removed. Connected (2) snap wires, pushed them back into the oven wall, used plyers to re-connect the element to oven. Installation DONE!
Turned on breaker and then the oven; we are now baking again.

It was real easy all I had to do was turn the breaker off,Undo two srews and disconnect the two wires. Then repeated the process to install

Removed to screws holding the bake element in place. pulled out element to get to the 2 electrical connectors. removed connectors from old unit. connected new unit and secured with the screwes. very simple.

unscrewed it unhooked the wires and replaced with new part

Removed oven door & shelves. Removed the 2 mounting screws & compared parts to verify I ordered the right one, then plugged it right in! Managed to drop & lose one of the screws while re-installing them. Got a stainless sheet metal screw from the hardware store that fits, but will probably order an exact replacement because the size & thread are slightly different. All in all, other than losing the screw, it was a quick, easy task.

1. Turned breaker to the oven to the off position.
2. Removed screws from back of oven-This was the most difficult part of the entire process!
3. Pull out element about 3", then tugged a little harder to expose the wiring.
4. Unhooked wiring from element.
All of this took about 15 minutes.
When new one arrived (less than 48 hours), I did the reverse of the above. This took about 6 minutes replace with new element. Thanks so much!

With less than 24 hrs from ordering to delivery, I was making cookies. Installation was quick and painless.

Removed two scres that hold element in Place. Pulled out element about 3" and removed wire disconnect. Re-connected new element and re-installed mounting screws. Very easy. Parts were delivered promptly. Great service!!!! Thank you Parts select!!!!! Saved me a trip to Sears to purchas a new element or Stove.

Piece of cake. Pulled range out, unplugged it, opened stove, unscrewed element from back of stove w/ socket wrench, pulled out 1/2 way, unplugged bad bake element from the 2 wires, plugged in new bake element in, reattached to back of oven, plugged in stove and it worked.

Remove two screws holding element. Pull element forward exposing connections. Pull connections apart. Replace with new element. replace screws. Done

First I removed the two screws holding the element to the back of the oven. When I pulled the element out I disconnected the two wires and removed the element. I found the serial / part number on the existing part and order from PartSelect. The element arrived two days sooner than expected!! Replacing the element was a bit more difficult in that I had to pull the stove away from the wall and remove the rear cover in order to pull the wires and element through the insulation in the back of the oven. Four screws held the rear cover, but once those were removed the element easily went into place and the repair was finished. Cleaning behind and under the stove took a few extra minutes but the entire repair only took about 30 minutes, plus the wait time for the part. Two tips, pliers were used to disconnect and reconnect the slip-on connectors. The connectors were pretty tight and reaching to the rear of the oven was difficult to get leverage to pull apart and reconnect. Also, the oven light caused considerable glare on my glasses so I taped the door button controlling the oven light and used a flashlight to see inside. Otherwise, a simple repair. PartSelect had the best price on the element and service and delivery were excellent!

Simply turned off the power (circuit box). Unscrewed the screws holding the element in place and detached the element from the wires. Replaced with the new element and replaced the screws. Turned the power back on. Easy as pie and saved lots of $$!

removed two screws, pulled element out (which broke at the sparking site) Took screw driver to push off where the element was connected. Put new one in, re-did screws. Turned on and off oven. This company was great to work with, smooth sailing. It was funny when we noticed the problem-Husband said $125.00 repair, I got on net and said no about $40. He is taking me out to dinner tonight.