91193218991 Kenmore Range - Instructions

I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.

Remove screws on bake element and on back cover to wires (unplug unit first) remove terminal ends , replace element put cover back on and screw in element hold down screws.

I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the burner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you

This oven is 2 years old and the element should not have broken like it did. GE is doing something wrong in the making of their ovens.
My husband took out the old broken element and attached the new one.

Easy

My baking element burned out after being exposed to grease and other remnants of past feasts. After some research the repair seemed straight forward so I figured I'd give it a shot. Overall it's fairly simple, though there are some things to watch out for.

I didn't remove my oven's door, which restricted my movement somewhat. After removing the bolts I was able to easily remove the old heating element and expose the two connecting wires. One wire had much more slack than the other. I connected the wire with more slack first. However, I'm somewhat uncoordinated and doing so caused the other wire to retract within the unit. I had to pull out my stove and remove the back panel, which was easy. The retracted wire was easy to find, but there was no slack available through the back access either. I actually had to unscrew the wire from the thing that is connected to the wire that plugs in to the outlet first. Doing so gave me enough slack to connect the heating element to the second wire. After that I just reconnected the wire to the outlet connection and put the back panel back on!

About 45 minutes in total time. Most of which was figuring out the approach to getting enough slack to connect the second wire and working around the oven door which restricted my movement.

Unplugged oven.I opened up back of oven the connectors to the heating element were showing. disconnected the wires(they just pulled off)went inside oven took the 2 screws out and pulled old heating element out. Put new element in and fastened it with the 2 screws. Went to back of oven slid the connectors together.Put back of oven back on plugged it in and started the oven. It worked

Saw the repair on YouTube first, to get the general idea. Very simple after that.

Mice took over trailer, after eliminating mice, and cleaning oven and range thoroughly, I noticed that the only place the mouse urine smell was still coming from was the vent tube. Noticed soiling around tube where it went through and into oven. I removed the center rack, layed some foil to catch any debris that may fall from the tube when it is removed. I removed old vent tube simply by removing the two nut screws on the roof of the oven. I had to pry it out a little bit. I then cut out and soiled insulation with razor knife, I inserted the new vent tube from the inside, and replace 1/4 nut screws and tighten.

Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes

I checked prices on the internet and found your price the cheapest and ordered the part on a holiday. The part arrived in two days and was installed and back to work pronto. Having worked in sales at Caterpillar Inc for a lifetime, I know how important quick delivery and short downtime is to our customers and you came through for me. I am satisfied with my experience dealing with your company.

burner went out Thursday evening, ordered new burner at 8:30 pm, new burner was delivered Saturday afternoon, removed back panel from range, removed burner, replaced burner, re-installed back panel. Took less than 1/2 hour to replace. Hardest part was finding the correct size socket.(ALL WITHOUT HELP FROM HUSBAND.) Thanks so much for prompt delivery.

Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one

The element ignited and burnt like a sparkler. I unscrewed the bolt/screws holding it in, and pulled like I had on older models. The clips holding it didn't come undone, but the wires hit the side causing a huge flash. It was still hot, even though it wasn't turned on. You need to unplug the oven, or turn off the breaker. I unplugged and took the back panel running down the middle off (4 screws), and undid the clips. Putting the new one back in was easy. Insert the element ends through their places inside the oven. Screw them in place. Hook the wire clips on in back, and replace the back panel. Installation took less than 5 minutes.