36275702001 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Laughlin, NV
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
none
slid the old ones out and slid the new ones in. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from San Francisco, CA
- Parts Used:
- WB19K10001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Oven will not preheat. Pulses on an off.
Turned off the gas. Disconnected gas inlet, burner supply line and oven supply line from regulator. Unscrewed regulator from its bracket. Replaced with new regulator in reverse order and added teflon tape suitable for gas lines to all threads.
Unfortunately, the regulator was not the cause of the problem and the oven still does not prehead - acts exactly the same.
Unfortunately, the regulator was not the cause of the problem and the oven still does not prehead - acts exactly the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Indio, CA
- Parts Used:
- WB29K10004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
we had damaged the burner cap
just removed the old burner cap and put on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Akshay from Bridgeton, NJ
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner had uneven flames
Too easy a five year old could do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurindalva from LODI, NJ
- Parts Used:
- WB28K10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No problem
I used a nutdriver to remove the natural gas orifice and I placed the other liquid gas orifice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from SAN JOSE, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks very old and writing on knobs worn ff
Very was ti replace racks and knobs. Very fast mail service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Solomon A from COLLEGE PARK, GA
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from CHICAGO, IL
- Parts Used:
- WB34K10013
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Edge around the burner area rusted and chipped off (both burners) on Right Double Porcelain Pan (or Spill Pan)
First, hand lifted and removed front and rear burner grates. Second, hand lifted and removed front and rear burner caps. Third, hand lifted and removed the bad Right Double Porcelain Pan (Spill Pan) from the range surface. Then clean and remove dirt, grease, stain on the range surface and around the burners area as needed. Lastly, replaced the good Right Double Porcelain Pan (Spill Pan), burners caps and burner grates in the reverse order as you removed them. Done in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Bakersfield, CA
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
broke tubes while cleaning under top
was still using back burners while waiting for parts (after safety check). I unplugged the electric for the igniters, raised top, installed tubes, checked for leaks with soap solution, closed top, plugged in electric tested burners. Got a big hug and kiss from my wife.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEAH from YUMA, AZ
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
tube that sends gas to burners broke both left and right front this happen due to opening the range hood to clean inside
I turn gas off to the appliance then I remove the old gas lines and installed the new ones. I did find it easlier to attach the line at the burner knob first then attach it to the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAPHNE from CHICAGO, IL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
while cleaning I broke the tubes either lifting or closing the top.
I bent the tubes very slghtly to rech the area of attachment. I first screwed them with my hand then tightened them with an adjstable wrench. It was really simple and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!