79095321302 Kenmore Range - Instructions

my dad and i did it together and it was easy. just had to remove the screws on the outside oven door pull the door apart, remove the old glass and put in the new and put the screws back in. hardest part was to get some of the screws out because they had been in so long.

It went okay but I had to have some help putting it back together. One person held the glass while the other person tightened the screws.

took screws on outer sides and then removed glass put in new glass replaced screws done

Snapped in the plastic piece after I actually ordered the right piece....wasn't paying enough attention when ordering and didn't have a book that showed the image so I could make sure....went off the image on your website......which is awesome. Totally my fault. Thank you for your wonderful service.

Part of one of the glides was still inside the hole so had to use a screwdriver to push it on out and simply put the new glides in both rear holes "very easily". Sure am glad I found this site on line. If anything else goes wrong, I will surely contact this site. Thanks. The speedy service was wonderful too. Got it in two days! Carol A. Lawless

Very simple with instructions supplied, Removed two screws inside on back of door, then removed four more screws to get to inner glass,removed broken glass installed new glass, replaced all screws.Job completed. very good instructions,Thank You.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....

I watched the repair tutorial and followed the instructions. The order went very well and the tutorial was spot-on. Nice.

First I watched video on how to repair oven door glass. The important part was how to remove oven door! If I would have watched the video before trying to clean the inner glass, I would not had to do the repair in the first place! After that everything went fast and smooth! I was very impressed on how fast I received the replacement glass from Part Select.... less then 24 hours! Thanks again for the quick service!

This was the easiest do it yourself repair job to be had so simple just push the new clip in the hole and you are done so easy. Audrey

Disconnected power first. Removed 4 screws on the back of the range, pulled the knob off of the switch, removed 2 small screws on the switch(on the front , under the knob) pulled off the 4 wires with spade connections on the switch. Put wires on the new switch, put in 2 screws on new switch, pushed knob on switch, replaced back cover and tested the new switch. Works great. Took less than 10 mins.

I am a total non repairman. but with the video on how to I did'nt even brake the first part. ( I ordered 2 just in case)Will use you ror every part!

Initially we realized there was a problem while cooking with the large eyes and we began hearing an electrical short behind the control switch. I unplugged the power from the oven/cooktop and removed the back panel where I could visually see soot on the switches where it was shorted. Careful while choosing your part from the diagram on Partselect.com. For the model FEF336ECJ, atleast for my oven, the eye switches were reversed and I ordered the small eye's switches! Luckily they have an outstanding customer support and immediately mailed out the new parts and a label to send the wrong parts back. Changing the parts out was very simple. Pull the oven out and UNPLUG IT from any electrical outlet. Remove the back panel. Double check from the label on the front of the control panel that you are working with the correct switch, and before removing the current switch, remove the wires one by one and place them on the new part to make sure you don't misplace these wires. Once the wires are connected to the new part, pull the plastic knob off of the old switch to reveal the screws on front of the panel. Place the new switch where the old one came from and fasten the screws back in place. Replace the knob, replace the back panel(for safety) and test the new switch before you push the oven back into place. If you can turn a screw driver, move the oven, and unplug the power, this easy do it yourself repair will save you possibly hundreds by not calling a repair/handyman who would absolutely love you to pay out the nose for such an easy task.