2783528610 Kenmore Range - Instructions

Ignitor is easily reached by removing the bottom of the oven floor. Machine screws remove easily when appliance is relatively new, but from experience, they may give you some trouble when stove is 5+ years old! Our part came in a timely fashion, even when ordered over a holiday weekend . Replace ignitor just as the old one came out-one word to the wise...scrape off enough silver coating on the wires so that a good contact is insured before splicing with the wing-nut included. Having had many GE stoves, I notice that the factory-installed ignitors have a shorter and shorter life; I'll be keeping PartSelect's website handy!

Diagnosed the problem as igniter failure and called local parts outlet. They gave me the part number, but said they were out and directed me to another vendor. When the part came, it was the wrong shape but I tried it anyway. Result - the igniter glowed which allowed the gas to flow, but igniter, being the WRONG PART, didn't ignite the gas, allowing a dangerous build-up of gas.

I then went to PartSelect, looked up the part, saw it was the correct one, ordered it (arrived within 3 days) and, because I already had the pans and covers off the oven, it was a matter of minutes to install. Works like a charm and, though I usually like to buy locally, I'll check out PartSelect first next time!

I removed the 2 screws that held the bottom oven plate in place. Then I removed the one screw holding the bottom burner in place in the front. I then reached into the rear area and unscrewed the last 2 screws securing the burner. I disconnected the igniter wires at their push-on connections and lifted the whole burner/igniter unit out. I relaced the igniter using the 2 attachment screws, and I cut the old igniter's wires with connectors and spliced them into the new igniter's wires, using the ceramic wire nuts that came with the new igniter. I reassembled the unit and it worked first time.

It was a simple repair removed the oven door, and the oven bottom plate. removed the screw that held the burner tube to gain access to the two screws that hold the igniter in place clipped the wires. put the new one on with butt end wire connectors instead of the wire nuts supplied. screwed the igniter back onto the burner tube put the burner tube back in place and secured it with the screw, replace oven bottom and door the whole repair took 20 minutes.

IThe schematics on the website were helpful for how everything goes together. I just followed the picture and then unscrewed all the screws that held the ignitor to the gas pipe. Have to pull out the gas pipe out first so you can get to the bolts, easy to do when you pull out the drawer and unscrew the hold down for the gas pipe.

No directions came with the part, and the length of the new wires weren't long enough nor did they have the attachment pieces that are needed to plug in the wires. However, helpful tips from others on the website told me that you have to cut the wires off the old part and screw the wires from the old to the new with the white plastic wire couplings. Worked like a charm!

It was a simple procedure, and I saved myself buying a new stove or paying someone else to fix it!

I removed the bottom pan and then removed the flame extender to get access to the igniter. I removed the two screws and cut the wires. I then wired the new igniter and used the ceramic wire nuts that came with the part. After that I installed the igniter. It was very easy to do this repair.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...And then I installed
ignitor tightening the two screws and connected the two ignitor wires with the provided wire-nuts.
Mike Polcho

I figured out the problem, ordered the part, and replaced it. Four hex head screws, two wire nuts, and two thum screws latter it was working.

I was able to access the burner and igniter by removing the broiler drawer. The flame guard was removed with a nut driver and the old igniter with a phillips screwdriver.

The electrical wires had to be spliced into the old igniter wires as they did not come with the factory connectors. However sire nuts were supplied.

After replacement of the igniter with the new one .. it would glow and about a minute later the gas would come on. However the gas from the burner did not light. I had to adjust the bracket closer to the burner to correct the issue.

Note: The igniter is wired in series with the gas valve. This means that it will continue to glow even after the burner lights durning oven operation.

After removing two layers of the oven floor I could not get at the igniter's wire connections. I found out that the new igniter was shipped with two wire nuts made of porcelain instead of plastic, so they were heat tolerant. Because of this, I was able to unscrew the original part and just cut the wires. I then installed the new igniter and spliced the wires of the new part to the cut wires that lead to the old part using the porcelain wire nuts and tucked the connections out of harms way. It worked fine.

Remove the broiler pan to get at the 2 nuts that hold the gas burner, remove them and then you can get at the 2 nuts on the back side of the igniter.

i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!

I rempved the top and bottom doors, than the wire rackes followed by the bottom base of the oven. Then I removed the burner cover plate so I could get to the igniter.. I removed the cover plate for the wiring (2 wires), unpluged them, removed the igniter (2 screws). I had to cut the wires on the old igniter and couple the ends to the new igniter and then replaced everything by just reversing all that I did. Simple! Easy!

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.

i went for 3 months waiting on the electrician who never came then asked the plumber who else could fix it and he said my husband could it only needed to unscrew 4 tiny screws and unplug and cut and twist wires back the hardest part was reaching the bolts hooked to the ignighter the burner was in the way and is not as easy to remove as someone has said all in all it saved us 100 dollars and could have saved us months of burning food trying to cook on broil if i had only called the plumber first.ha ha