79075864300 Kenmore Range - Instructions

Remove two screws from bottom of inside oven door slide oven door up of hinges in side of door has 2 more screws when removing hold handle it does come off at very bottom of door remove all screws cover comes off remove new glass from package and place over brackets put oven door cover back on put screws back on slide back on bracket put last screws on

I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connected them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.

1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

replaced it

On this website, I found an instruction manual for this stove. There were 2 pages about how to change the glass on the oven door, including diagrams. I'd also checked a generic youtube video on changing inner glass on oven doors too, although the hinges in the youtube demo weren't exactly like those in mine. I printed out the instructions, checked the oven door to make sure the hinges looked like those in the diagrams, set aside a couple of hours on a free day with no other distractions, and did the job. I just kept removing screws from the inside oven door, peeling back the layers of the onion, until I got to the innermost glass, which was cracked. Put the new glass in, put it back together. On youtube the guy said it would take 20 minutes. It took me about an hour. Saved a ton of money by doing it myself.

Followed service sheet. Measured 2.6 amps draw at igniter wire which should have been 3.2 amps. Replaced igniter and problem resolved.

This was a very easy project.
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repaired our stove myself!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.

First, I read all the instrutions that came with my replacement part from Parts Select thoroughly (twice) then follewed them like an experienced surgeon. I removed the lower drawr after turning off the gas and unplugging the stove and then took out the bottom panels inside the oven to expose the screws holding the ignitor coil. Removed it, then cnnected the new one to the existing wires as they were in the stove and the drawing in the instructions, then replaced everything in the reverse of them coming apart. Plugged it back in, turned the gas back on and now it,ll bake things again. YEAH!! Parts Select!!!

the igniter is real easy to put in

removed the old igniter, installed the new one. 15 minutes, piece o cake!

followed online instructions

My husband was able to easily remove the old part, and replace with the new ignitor. The wires were long, so he took the extra precaution of tying them away from the flame. It took longer to take everything out and put it back together than the actual repair..

Let me begin to say your service was great. I received the unit the next day. Also your price was good.
The whole job took me an hour. I would have done it sooner but I didnt a square head driver bit to remove the igniter from the burner assembly. I removed the whole assembly and with a pliers slowly unscrewed the mounting screws. After that I disconnected the igniter per your instructions,spliced the remaining wires reconnected the gas and electric and I was good to go.