9114654190 Kenmore Range - Instructions

First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..

At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!

I removed two small screws located on the underside of the control panel. I then rotated the bottom of the control panel up and dislodged the few connections at top back of control panel. The control panel became loose enough to lay forward exposing the inner control switches. The old problem switch wiring was removed one by one and placed in the same spot on the new switch. The old switch was then removed by pulling off the front control knob and then unscrewing two screws holding the old switch in place. Then the new switch was installed exactly as the old switch was removed.

Cut Wires to old terminal block and wired in new Terminal Block

Turn off power at the circuit breaker before working on electric thing.

Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.

I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!

i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!

took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.

REMOVED 5 PHILLIPS SCREWS
REMOVED BROKEN RT CAP
INSTALLED NEW END CAP
REINSTALLED THE SCREWS
PROJECT COMPLETE

I basically had to disassemble the top part of the stove to get the clock out. Once I got the clock out, replacing the plate was trivial. It attaches with a sticky/tacky back. Reassembling the stove took another 30 mins, but went relatively smoothly. The final job looks great and the stove seems to function as usual.

1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two retaining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake

Easy

I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. I then secured the new unit to the oven wall with the two screws.

My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.

First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and reconnecting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.