79072863302 Kenmore Range - Instructions

Simple: remove the element by hand and replace new one.

I can't believe how quickly I received my new part -literally next day.

First, I unplugged the oven from the wall. I opened the bottom drawer of the oven to see where the igniter was mounted, which was directly under the bottom pan of the oven itself. I opened the main oven door and unscrewed the 2 screws that were holding the pan to the bottom of the oven. Then, I slid the pan back towards the the back of the oven and it popped right out.

There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.

Plugged it back in, turned it on, fired up within 20 seconds. Good as new.

Ordered new racks and replaced them.

Twisted replacement bulb into place easily. Let there be light!

Removed oven door. (Open to first position then lift the door straight up). Located igniter in bottom of oven, followed connecting wires to connection block below oven behind the oven drawer. Disconnected the existing wires. Lifted the burner out of oven to disconnect defective igniter. Screws were fused to the burner. Used vice grips to remove screws requiring the screw holes to be retapped. Bought new screws to replace trashed screws. Installed new igniter to the burner rail then set burner rail back in place. Fished the leads from new igniter back down to connector block. Reinstalled leads. Reinstalled oven door. Tested functionality of oven. Everything worked. Reinstalled metal plates back in oven. Reinstalled cover over connection block behind bottom drawer. Reinstalled drawer. With the exception of fighting with two screws fused to the burner rail it is a very straightforward repair and shouldn’t take much more than 1/2 hour.

Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed new ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

had to use a tap and cut new threads. Also had to remove the top of the range, and the metal cover under the top.

get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.

Turn off gas,unplug,unbolt the burners(you have to do this to keep from bending and or kinking over the gas lines.Luck kept me from bending the lines out of whack.)All I needed was the electrode but I couldn’t find it available separately.I had to buy the whole front burner.Anyway remove the clip from the new part slide the electrode out.Tilt the top of the range up take the clip off of the old electrode slide it out put the new one in install clip.Plug it in,rebolt all the burners in.Careful not to bend the gas lines.put the top down turn on the gas,plug it in and light.

The hardest part was pulling the oven away from the wall. Two bolts hold the sensor in place and a clip connects the electronics. Replacing the old one was trivial.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

ordered a new part,from partselect

First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!

It was a replace racks not repair. No problem