9116408810 Kenmore Range - Instructions

First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..

Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power

I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorced mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

Removed the door. Unscrewed the hinge from front of oven. Took broiler drawer out. Unhooked the spring. Removed hinge. Screwed new hinge in. Rehooked the spring. Slid oven door back on hinges. Mission accomplished. Oven door works like a champ. Wife happy.

i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven

Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:

At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!

Fast shipping, Very easy to install I am a senior and had no problems works Great!!

Followed the excellent removal and installation video by PartSelect. Also the diagram was excellent allowing me to purchase the correct hinge the first time. Fast shipping.

Bent the tips so the phillament can fit inside the oven.