91136655794 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven door hinge wheels were worn out and grinding.
Followed the online video. Unhooked the springs, removed the 3-screws on each side. Installed the new hinges in reverse order. Used the wear marks on the old springs to ID and place the new springs in the holes on the new hinges. Great company to deal with....never a surprise, Great communications letting you know that your parts were on order and then again that they were shipped with shipping info and numbers to call with any questions. The best part has been that the parts drop right in everytime I have ordered from them!!!! Thanks Dan!
Was this instruction helpful to you?
Thank you for voting!
Nylon Roller On Both Hinges Wore Out
Watched the video and did exactly as it instructed. Very easy to do, took 10 minutes in all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hopeland from Jamaica, NY
- Parts Used:
- WB36X754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My Oven Light Lens Cover Was Broken
I could not get a lens cover due to the fact ge does not make any more since the appliance is an older model. Thanks to part select they had the part which I badly needed. It was easy to installed. Thanks again part select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Marietta, GA
- Parts Used:
- WB2X9151
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light in oven had blown and needed to be replaced
I did not do it, I instead had my neighbor put the gasket around the light lens cover and replace it. He considers himself a handy man, so it was easy for him.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from North Windham, CT
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Plastic roller broken
Smooth and quick. Fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Laguna Hills, CA
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Left rear burner would not light
Began by removing the front panel where the range handles are located. There were 7 screws located under the panel which required opening of the oven hood. All of this removal was a waste of time, because the range top was on hindges. The only thing holding ithe range top down was the accumulated grease and oil along the edges. I used a screwdriver to sperate the range panel. There were side supports to hold the the top up, like a car hood support. Replacing the electrode was a snap after that. Overall, it took less than 30 mins but it would have taken less than 10 if I hadn't removed the front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Black River Falls, WI
- Parts Used:
- WB14X103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The left hinge broke
It was really easy, and my only problem was getting the 3 screws out. I just used some WD40 and liquid wrench to free up the screws. After those were out I was in BUSINESS!!! I then just screwed in the 3 screws, and used my needle nose pliers to reattach the spring and WA-LAH!!! Done deal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Sandy Hook, CT
- Parts Used:
- WB14X103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Range door was hard to open and would not close completely
I watched the video in the website and in less then 5 minutes replaced the broken hinge with the new one and the door works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Jenison, MI
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no spark at burner
Remove grates,pans and disk. Remove allen screws at each burner. Take a flat blade screwdriver and press in on tabs on each side of front of stove to depress keepers and lift top up. Remove wire, and keeper on bottom of electrode. Reverse for install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Granville, NY
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Plastic Roller on hinge broke in half
Following the repair video made the job very easy and quick, about a 5 minute repair. Wife says oven door never worked better. Thanks a lot for all your help.
Was this instruction helpful to you?
Thank you for voting!
one oven hinge broken
It took longer to watch the video on how to replace the hinges than it did to replace them. Simple and easy. Video knocked it out of the park for ease. And now the oven door works great! thanks!!!! Video suggested if you're replacing one side do both, couldn't agree more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from East Moriches, NY
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken roller on hinge
I unscrewed the broken hinge, removed the tension spring and replaced the old hinge with the new one. total time 5 mins works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sandstone, MN
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Valencia, CA
- Parts Used:
- WB31K5092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Wanted to replace old burner bowls on stove top
Repair was easy once I got the correct part. When the parts were listed as small and medium large I thought they were talking the diameter of the bowl. It turns out they are talking about the center hole in the bowl. So I needed one small and three large. Everything great now.....stove looks great and clean.
Was this instruction helpful to you?
Thank you for voting!