66572174301 Kenmore Range - Instructions

The web site was easy to navagate and locate the correct part. The part was in stock and shipped the next day and was delivered in 3 or 4 days. All total the replanement was less than a week. The replacement was easy except it took a second person to hold the glass in place while i threaded the hold down screws fron underneath. I could not hold the glass and thread the small screws with just my two hands, plus having to thread the screws from the bottom was more difficult, but all in all it was simple and now we have a new unbroken glass front oven door.

According to the manual tucked behind the oven, if one solenoid on the gas safety valve/regulator doesn't work, neither will work. It indicated that from the center (common) pin to each of the others, it should read 216 ohms. Mine read 200 to one side, none to the other. I ordered a replacement, had a buddy tip the oven up for easy access while I went at it with a screw driver and some line wrenches. Swapped it out and she works like a dream now.

Replaced igniter

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

I was able to perform this repair without removing the oven door. Removed cooking racks (2) Removed oven bottom (2 screws), removed flame spreader (2 screws). removed igniter (2 screws - used a 5/16 hex socket wrench). On this model range the lower screw on the igniter is on an angle (about 45 degrees) and very close to the heat reflector pan; patience and perseverance was required to remove it. - do not know if there is a special tool that would help making removal of this screw easier. If it wasn't for this one screw, the repair should take about 15-20 minutes. Replacement of the igniter solved the ignition problem.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

switched out latch asy,rear

Checked to see that I had all the parts I needed.
Installed bottom door trim then side trim pieces.
Do not tighten screws. Install door handle with top
trim attached over glass. Tighten screws just snug
all around.

Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

This is a very simple repair. 1st shut off your gas. Disconnect your gas line from the gas shut off value to the Gas Safety Value(GSV/R)/Regulator. Disconnect the other 2 lines attached to the GSV/R. Remove the 4 mounting screws holding the GSV/V. Wiggle the GSV/R from its location. Carefully remove the 3 wires connected to the GSV/R. Install your new GSV/R in reverse order applying sealant to the threaded joints. test for leaks.............. your done!!!

I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

ordered new front and replaced

First I removed the gas line from th wall. Second I removed to gas lines going from the regulator to the stove. The regulator then unscrewed from the stove itself and that was it. I reversed the process to install the regulator.

Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.