79079019102 Kenmore Range - Instructions

removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since

Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.

Open the door and slide in the new rack.

I unplugged the stove then pulled the disconnected the wires that controled the igniter. I took the two screws off that held the igniter to the pilot port. I hand to cut the wires on the new igniter to some-what match the lenght of the broken igniter. Then I cut the connectors from the old part and used the fire resistant wire nutes that where included with the new igniter and connected it all. Put all the screws in tight, double checked every thing. Finally I plugged it in and it was working.

First I removed the two screws that held the element in place.I then pulled the element out and cut the wires.I used wire nuts to put the new wirers on and put it back in place with the two screws.I tried it and it worked perfect.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!

Turned the gas and the electricity off to the gas range. Took the two large screws out in the back of the range holding on the first pan. Have to look for them. Took off the single nut holding on the second pan. Used nut drive #10 to take off nuts. Be careful you do not lose them. Took off inoperative unit. Cut wires to unit. Stripped wires which connect to range. Put new unit on and tightened nuts with nutdriver. Spliced wires together and put on wire nuts securely. Taped them to the wires. Put the second pan back, then the first pan. Turned on gas and electricity to test.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.

had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
And re-connected the same way.
Peice of cake..

Thank You..

take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard

remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.

Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?

Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.

AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.

First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom cover, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.