2783288690 Kenmore Range - Instructions

I removed the oven burner while the igniter attached. put unit on my bench and changed the igniter and reinstalled the burner and reattached the wires to the supply terminals. Tested the unit and it lite up ok.

Removed bottom tray of oven, removed ignighter, unplug two wires.

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my plan :)

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?

simple remove & replace. 2 min job. Couldn't be happier.

I took the old igniter out and replaced it with a new one.

The stories posted on your web page are great - only improvement would to add a schematic of the parts being removed - no issues were encountered - great service by the way - part arrived the next day - a Saturday!

John M.

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

We follow the advise of one of you other viewers. It was so easy. Our thanks for the info and the speeding delivery

followed peoples advices and all went very smooth. make sure to undo bracket from behind bottom drawer as it will make your life much easier.

The range still worked and the broiler still worked. I noticed that the ignitor for the broiler turned on and glowed a short time after starting the broiler. I dissembled the floor of the oven (just two screws) and tried the same for the oven, but the ignitor did not start or glow. I ordered the part. It was sent withing two days. It was easy to replace and the oven has worked well since. I recommend ordering the attachment fixture as well, in that taking apart the one that held the old ignitor immediately stripped a screw and I ended up bending the fixture and having to reshape it (the small extra cost will be very well worthwhile!)

1) use screwdriver to remove screws securing lower pan in oven (screws are at back of oven)
2) remove lower pain to expose igniter and burner
3) remove lower storage drawer
4) disconnect 2 igniter wires from where they are attached underneath
5) use nutdriver to remove burner from above and below (this makes it easier to remove the igniter)
6) use nutdriver to remove the faulty igniter
7) cut off clips from faulty igniter leaving enough length to strip and then attach with ceramic caps to new igniter. (be sure you attach the right clip to the right wire)
8) reverse the process to install the new igniter.
20 minutes tops

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

We found the part right away from the diagram provided by your web site. We located the part number easily, paid on line and received in part in two days. My husband fixed it. It was relatively easy. Saved us money to pay someone to fix it. It could easily cost us more than $200.

I removed the bottom drawer, disconnected the wires and then using the socket driver removed the screws holding the burner in place from below. I then unscrewed the bottom plate of the oven from the top so I could get to the burner. I unscrewed the one screw still holding the burner in place. Disconnected the old igniter and then cut the cables at an appropriate length so I could re-use the connectors on new igniter. Spliced together using wire nuts provided, mounted new igniter to burner, put it all back together and it fired up like it was new.