2783138817 Kenmore Range - Instructions

We found the part right away from the diagram provided by your web site. We located the part number easily, paid on line and received in part in two days. My husband fixed it. It was relatively easy. Saved us money to pay someone to fix it. It could easily cost us more than $200.

took the bottom plates off with philips screwdriver.(note) there are two plates..outter and inner..to get to the two screws on the igniter.Remove igniter(two nuts). Install new. Cut the wires from old(lower part of oven and rewire with porclain wire nuts.Very simple...Partselect was great too..very fast shipping. Will do buisness again.

followed peoples advices and all went very smooth. make sure to undo bracket from behind bottom drawer as it will make your life much easier.

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?

Took off the 2 bottom covers, saw the igniter did'nt glow, checked for voltage,yes.Ordered part. when had part,pulled out ignitor,respliced wires, and did in reverse order.

I removed the oven burner while the igniter attached. put unit on my bench and changed the igniter and reinstalled the burner and reattached the wires to the supply terminals. Tested the unit and it lite up ok.

I removed the bottom drawer, disconnected the wires and then using the socket driver removed the screws holding the burner in place from below. I then unscrewed the bottom plate of the oven from the top so I could get to the burner. I unscrewed the one screw still holding the burner in place. Disconnected the old igniter and then cut the cables at an appropriate length so I could re-use the connectors on new igniter. Spliced together using wire nuts provided, mounted new igniter to burner, put it all back together and it fired up like it was new.

I removed the oven grates and removed 2 screws that held the bottom pan in the oven to get easy access to the burner and igniter. Remove 2 screws that held the burner in place. Removed wire nuts. Removing burner allowed easy access to fasteners holding ignitre in place. Confirmed that the igniter was bad by checking the continuity. Ordered part later in the evening from parts select. Part was here 2nd morning after I ordered it. Installed, and checked to make sure igniter wasworking properely. When check confirmed igniter was working, replace oven components. Saved myself $100 or more by doing it myself rather than having a repairman out.

The range still worked and the broiler still worked. I noticed that the ignitor for the broiler turned on and glowed a short time after starting the broiler. I dissembled the floor of the oven (just two screws) and tried the same for the oven, but the ignitor did not start or glow. I ordered the part. It was sent withing two days. It was easy to replace and the oven has worked well since. I recommend ordering the attachment fixture as well, in that taking apart the one that held the old ignitor immediately stripped a screw and I ended up bending the fixture and having to reshape it (the small extra cost will be very well worthwhile!)

Part arrived day before thanksgiving bent old igniter back and forth till broke off then easily took out screws.Cut and strip old wire, screw on new ignighter this was tough to get a wrench on with the positioning but after connecting those wires and slappin the rest of the oven back together one turn of the temp knob told me thanksgiving was going to happen Thanks to part select I was lookin like a hero!

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstalled protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.

1) use screwdriver to remove screws securing lower pan in oven (screws are at back of oven)
2) remove lower pain to expose igniter and burner
3) remove lower storage drawer
4) disconnect 2 igniter wires from where they are attached underneath
5) use nutdriver to remove burner from above and below (this makes it easier to remove the igniter)
6) use nutdriver to remove the faulty igniter
7) cut off clips from faulty igniter leaving enough length to strip and then attach with ceramic caps to new igniter. (be sure you attach the right clip to the right wire)
8) reverse the process to install the new igniter.
20 minutes tops

I removed the oven door, racks, and oven floor. That was easy, the floor had two thumb screws and one phillips/hex screw. I removed the lower drawer and the 2 covers above the drawer. The igniter was held in place by two phillips/hex screws. Had to manuver a bit to get the right angle to remove the screws. THE MOST IMPORTANT PART OF THE REPAIR, when you cut the two wires to remove the old igniter, cut them off as close to the old igniter module as possible. On my stove one of the wires on the new igniter was about an inch too short and I had to add a section of wire. Overall the whole job was easy. Keep track of screws as you remove them.

I first checked the power by pushing oven button, I heard the relay make a sound " CLICK" ,I then knew it wasnt the power .I then removed the oven racks and then I removed the the two screws holding the pan in place. I hit the power button and noticed the ignitor did not glow as it should.I ordered the part and replaced it and had frozen pizza 20 minutes later.