79075738891 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from Smithville, TN
- Parts Used:
- 316109512
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
took the new one out of the package and put it on. Took about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Lakewood, OH
- Parts Used:
- 5304497424
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gas Oven Overheating
Removed cover on back of range (four screws held it in place), removed screws holding the oven sensor in place, pulled out oven sensor and disconnected the snap-like connection, tested with ohm reader (was below 1000 and 1100), ordered new part (came next day), inserted the sensor, screwed it back in, snapped the connectors together, replaced cover on back of stove. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maura from Hingham, MA
- Parts Used:
- 316109512
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our original knobs were worn, ugly and disgusting...
I found the new knobs I wanted online through this website, I ordered 4 brand new ones. They came in the mail via FEDEX Ground and were and looked absolutely perfect! I love them, my husband loves them, they're awesome! Great job... :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Camden, TN
- Parts Used:
- 316085701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced inner oven door glass
First I watched video on how to repair oven door glass. The important part was how to remove oven door! If I would have watched the video before trying to clean the inner glass, I would not had to do the repair in the first place! After that everything went fast and smooth! I was very impressed on how fast I received the replacement glass from Part Select.... less then 24 hours! Thanks again for the quick service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ubly, MI
- Parts Used:
- 316101514
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
clock overlay was wore out and cracked
The repair went really well, from the time I talked with the rep on the phone it was twenty four hours later and the part was in my hands. Great service! Because it was just the clock overlay all it took was a screwdriver to take the panel off and peel the old one off a nd stick the new one on. I will use part select again in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from lexington park, MD
- Parts Used:
- 5303208499, 5303935068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven or boiler not lighting
removed gas safty and igniter .replaced 4 screws and 3/8 wrench. make sure you turn the gas off frist.after repairs are done make sure there are no leaks at fittings.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Manasquan, NJ
- Parts Used:
- 316495901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom Panel of over rusted out.
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Weidman, MI
- Parts Used:
- 316011200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Igniter electrode broke
The three bolts that held the burner busted off when tring to loosen. I drilled out the old studs and replaced with self tapping screws.
Was this instruction helpful to you?
Thank you for voting!