79075754103 Kenmore Range - Instructions

After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!

I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connected them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.

Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. Stripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.

Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.

I saw a chart of the oven door at site after I finally got the model number. I actually thought I had ordered the wrong part, third door in was last pane I thought, but actually this is inner most oven door, glass panel four. I had to find a correct screw diver which took awhile. I thought I didn't have the strength to turn the necessary screws, but easily could with correct screw driver. I followed other stories about removing handle, spring loaded door, so be careful it pops apart. A bit tricky to put back together, cause you have to hold door together against spring when you put cap on and door handle. Remove handle, remove top plastic cap. Will see screws holding glass and aluminum shield in place. Remove shield, need to remove screws holding glass two panes with holder. Shield pulls back and this glass just drops in. Reassemble door.

replaced it

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.

followed the instructions that come with the part. very quick and easy.

pulled bottom door out as far as you can. lift out broiler tray and the tray under that. to get the door completely out. on each side of the rail holding the door from come out push in the tap on each side and pull the door all the way out and off. reach inside and take out two nuts holding the old igniter and cut the two wires and remove it
stripe about 1/4 in of the wire. attache the wire from the new igniter. hold them two and use the white cap and twist it on the two wires and do the same to the other two wires. Bolt the igniter back on with the two bolts and your done. When you turn on the oven the igniter will click and turn on. it will be alot brighter then the old one and the oven will start pretty fast.

I exposed the ignitor through the inside of the oven and then removed the two screws that held it in place. I then cut the wires underneath the stove ans reconnected them to the new part with the wire nuts provided. It was a simple repair.

I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.