66575775890 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ann from Whitewater, WI
- Parts Used:
- 8184859
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The side trim was broken when I cleaned the door.
The repair was easy. I had to remove the trim on the other side and the bottom. You slide the new trim on and screw in the bottom two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from baltimore, MD
- Parts Used:
- WP179051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
missing screws for oven door
After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Sherman, IL
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven door would not lock for self clean
switched out latch asy,rear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from West Grove, PA
- Parts Used:
- WP3186491
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Gas Oven, started to Preheat then quit. Then would not even light
It is very simple to do. We called a repair man we normally use, but he does not do gas appliances. So started to research. I removed the bottom drawer, looked at the connection on the wires hanging down. Opened the oven removed the racks. On the bottom plate, loosened two screws and slid the bottom toward the front and removed it. Then removed two philips screws and removed the heat deflection plate, it slides forward and pulled up from the back. Then there it was- the igniter. I looked at it then looked at the connection behind the drawer. Went to PartSelect.com, found the part using the model number and used the parts diagram found the igniter and the picture matched what I had. I ordered the part, placed all parts back in place until part arrived. After part arrived, shut off breaker to oven removed all parts again disconnected the wire connection behind the drawer. Then on the side of the igniter, I used a nut driver, removed two bolts and took out the igniter. Matched it to the new one, including the power connection. Placed new one in and reversed the order. Turned on breaker, Pre Heated oven, been in service since. Ordered part before 3 on Wed, received early on Friday. Stopped home during lunch Friday and put it in place. 15 minutes and DONE Oven worked and fresh baked cookies when I got home! Thanks PartSelect.com!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles G from Apex, NC
- Parts Used:
- 8184859
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I broke one side of the oven door trim while cleaning
I removed the bottom srtip. Installed the new bottom strip, snapped in the side pieces. [The old ones screwed in.] Replaced the original handle. Ready to reinstall door.
Was this instruction helpful to you?
Thank you for voting!
Replacement of oven glass door
Parts arrived extremely quickly. Easy assembly. Would highly recommend partselect.com. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Marthasville, MO
- Parts Used:
- WP3186491
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Had to replace ignitor
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Replacing it was just as simple,only in reverse.
The only tip I have that I should mention,is to UNPLUG the appliance first,as 110volts tingle your fingers!
Replacing it was just as simple,only in reverse.
The only tip I have that I should mention,is to UNPLUG the appliance first,as 110volts tingle your fingers!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aires from Canton, GA
- Parts Used:
- WPW10118455
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broke glass door on stove while cleaning it
I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delores from Warren, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven light would not work--faulty socket
After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Pine Plains, NY
- Parts Used:
- WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven bottom had rusted out
Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bridget from Windsor, CT
- Parts Used:
- WPW10118456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drop the glass while trying to replace outer trim
My husband had no problem at all with the replacement of the exterior glass.
Slipped it in and attached to hooks and secured with the handle with a screw driver. Be sure to remember the trim doesn't cover the glass it kind of sits behind it. It can be deceiving in a way you may think in sits in front of the glass. Otherwise it was quite easy and the part came quickly in less than 24 hours....this is a great site.
Slipped it in and attached to hooks and secured with the handle with a screw driver. Be sure to remember the trim doesn't cover the glass it kind of sits behind it. It can be deceiving in a way you may think in sits in front of the glass. Otherwise it was quite easy and the part came quickly in less than 24 hours....this is a great site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Marion, KS
- Parts Used:
- WP3196262
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
oven light flashing off and on when door closed
removed the two screws that held the cook top on and moved it enough to get to the light switch. Removed the switch and tested with multimeter. Pulled the two wires out of the mounting hole and insulated with elect. tape. Replaced the cook top and installed the two screws that hold it in place. Located the switch at PartSelect on line and ordered it. When the switch came in (the next day), I connected the two wires, and snapped the switch in place, and I was back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from New Baden, IL
- Parts Used:
- WP3186491
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Igntr would glow but Oven wouldent heat
I removed the two screws that held the igntr in place. Then I pulled the igntr out and unplugged the wires. Replaced the igntr with the two screws and plugged the wires back together. I then turned the oven on to 400 degrees and it heated like a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Reynoldsburg, OH
- Parts Used:
- 8184859
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken trim
remove the hinge stays they just clip in
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.
Was this instruction helpful to you?
Thank you for voting!