36275944100 Kenmore Range - Instructions

Disconnect power. Remove oven door, oven racks, bottom pan, drawer below the oven. unsnap igniter wire connector. Remove two screws holding the igniter in place, remove igniter.

Install igniter (placing igniter wires away from any heat producing parts) and all parts in reverse order as they were removed.

Oven heats good now, makes great cornbread and biscuits, the wife helps the oven do this.

While I was waiting on another part to arrive, I decided it would be a good time to do a thorough cleaning. When I lifted the top of the range, I lifted it to far and cracked both front burner tubes. The top of the range should not be lifted more than 4 inches without removing the 3 screws that hold each burner in place. When the new lines came in, I removed both front burners, knobs, and then removed the front plate behind the knobs using a Phillips screwdriver. The screws are located on the bottom of the plate. Using my adjustable wrench I replaced the lines. Then I CAREFULLY bent the gas tubes and remounted the burners. Over all an easy install. Just be careful, the gas tubes are aluminum and will break very easy. This is the second time I used PartSelect, and I am very satisfied.

determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 year old oven,it was very easy/.

This was a real easy job and a success,of course any repair i do on a gas appliance and when finished It doesnt blow up i consider a success.
Thank you,David Williams

I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the igniter is the problem.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.

Took longer to open the box.

1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.

I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.

First I removed the broiler from the bottom of the oven, then pulled the oven way from the wall to unplug it. I then removed the two screws that hold the igniter element in place. Ironically, the plug GE manufactures is reversed so i had to strip the plug and go end and reverse the wires to attach them to the oven. I used ceramic wire attachments as plastic would surely have melted. Replaced the screws, replaced the broilers, plugged it in, replaced against the wall and it fired up.

Removed old line with wrench and attached new line to gas valve first. Then lowered hood to the stop and attached gas line to burners.........very easy and works fine now.

Turned off the gas. Disconnected gas inlet, burner supply line and oven supply line from regulator. Unscrewed regulator from its bracket. Replaced with new regulator in reverse order and added teflon tape suitable for gas lines to all threads.

Unfortunately, the regulator was not the cause of the problem and the oven still does not prehead - acts exactly the same.