66572179300 Kenmore Range - Instructions

On the back of the range was a little plastic bag with the range document. In this document was instructions on how to check out the electronic controls, a drawing of the electrical wiring and a digram of the gas line part of the range. First I did the electronic part and it check fine. Following that the instruction was to check out the solenoid coils for the bake and broil valve. I believe the wires were blue, red and orange(it tells on the wiring diagram). It called for 216 ohms on each coil. When I unpluged the plug from the circuit board on the upper right backside of control panel I checked the resistance for the two coils. One side had 198 ohms and the other coil had 0 ohms. The instruction said that if either coil didn't measure 216 ohms or close to that value the valve would not work. So, I wrote down the Model number. Next I checked the gas valve for numbers, wrote down all that was on the valve because I didn't know which one was the part number for the valve. Went on line to the Whirlpool site, once in the Whirlpool site I found out they have a diagram of parts for different appliances, pulled up the model I was looking for, found the valve( under the valve part, the number was different than the one I had, but the information said it would fit the model of appliance I have) order the part. In a few days the part arrived. I turn the gas off, unplugged the electric. I removed the gas lines, had just a bit of a problem with the short gas line going to the burner for the oven, when the line was out I unplugged the control wires. Nake sure you write down how thw wires are on the valve before unplugging. There is an adaptor on the valve to the main gas line. You need to take this off and put on the new valve. This is where you need the pipe cement. Stay back from the end of the adaptor that goes into the valve one or two threads with the pipe cement. you do not want to get any inside of the valve. Put the adaptor on, tighten, plug in the control wires, replace the valve on the stove, connect the gas lines, put all the gas lines on before you tighten them. Turn on the gas. Check lines with soapy water for gas leaks. Plug in the electric, check it out. Don't forget to put the instruction back in their little plastic package and I also put a copy of the order I had for the new valve just in case I need it in the furture.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

removed the two screws that held the cook top on and moved it enough to get to the light switch. Removed the switch and tested with multimeter. Pulled the two wires out of the mounting hole and insulated with elect. tape. Replaced the cook top and installed the two screws that hold it in place. Located the switch at PartSelect on line and ordered it. When the switch came in (the next day), I connected the two wires, and snapped the switch in place, and I was back in business.

Simply removed three screws that held the door trim in place. Once the screws are removed be carefull because the front door glass is held in place by the bottom door trim. Otherwise an extremely easy repair.

I took out the two screws that held the oven handle in place inserted the glass in the door and replaced the two screw!!! That easy!

I have removed this piece once before and painted it,
but it is difficult to prepare surface.

I tried to replace the part without removing the door
but had difficulty getting the screws to line up.

So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.

Door Trim went on easily and the oven door went back on quickly.

Surprised they don't make this trim piece with rust proof material.

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.

Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).

I had problem with the oven of the stove since the beginning. It wa difficult to start. Later, it stoped working. The technician told m that the gas valve regulator was the problem. That was the reason I decided to buy a new one. After installing it, however, the problem continues. The ignition starts, but the gas does not go thru. It seems the signal does not go to the valve to open the gas.

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

Removed two gas lines at the safety valve. Removed the four mounting screws and disconnected the three wires. Re-assembled in reverse order of dis-assembly. This was an easy diagnosis and repair/replacement. The PartSelect website is very easy to use if you have the model number and I like the diagrams to be sure the part is correct.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.