79045662103 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Milford, IN
- Parts Used:
- 318394803
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove door switch was broken
used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Artesia, NM
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Coil melted in half.
First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Glasgow, MT
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was not heating up to the set temperature. Stopped around 180-200F.
Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Reno, NV
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke
unscrewed old and screwed in new
Was this instruction helpful to you?
Thank you for voting!
Needed new drip bowls
The hardest part of the job was cleaning under the old rings. Cook top looks new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Union Point, GA
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element went out on my oven
Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.
Was this instruction helpful to you?
Thank you for voting!
drip pans old and rusted
unplugged the elements, removed drip pans, replaced with new drip pans. plugged back in elements. took no skills or effort. the parts were ordered on-line one afternoon and were on my doorstep the next morning. I had been unable to find drip pans that fit my stove and was thrilled that they fit and came so quickly and were reasonably priced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from ADAMSVILLE, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Weld Was Broken On Support Bracket On Element
Replaced element no problem?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lake Mary, FL
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Handle
Really easy to replace handle. However, because the new handle does not have the metal inserts to receive the attaching screws (!appearently a bit cheaper to make!), I am concerned that it will not last as long. I could find no reference to new attaching screws so used the old ones...hope it works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Dasssel, MN
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was not heating properly
I ordered the element. When it arrived, I simply removed the old one and put in the new one. However, it did not completely solve the problem. The heat is now distributed evenly, but still have to turn the burner to 7.5 to boil water.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Lawrenceville, GA
- Parts Used:
- 318293820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner on top occasionally went to high heat though it was set at low
Replaced the switch...removed old switch and transferred the wires one at a time to the new switch. Seems to working fine..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sharon from Summerton, SC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element not heating right
Took old one out and plugged the new one into place.
Was this instruction helpful to you?
Thank you for voting!