79045662103 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from addison, PA
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven not reheating after initial heat up
unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Spencer, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" stove top element would not warm up.
It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Elizabeth City, NC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was damaged
snap out the old one and snap in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Storm Lake, IA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dead burner
I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from ROCHESTER, NY
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element was cracked
Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia from NEW BADEN, IL
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven Bake Element caught fire
Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.
Was this instruction helpful to you?
Thank you for voting!
The switch for one of the electric burners burnt
I shut POWER OFF FIRST and tested it be fore I started. I left all but one wire intact on the old switch and when the new one arrived I made sure it was the right one(it was) and then I just removed one wire at a time from old switch to the new one. After the install was complete turned power back on tested it and it worked. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from HIGH POINT, NC
- Parts Used:
- 318255006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Heating element broken
I followed the instructions from the lady taking my order she talked me through the steps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rockie from KEIZER, OR
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
burnt out element
Followed instructions on website. Went perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Dayton, OH
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element burned out in my slide in range
Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashley from CARRIERE, MS
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element in our drop-in oven stopped working
We turned off the power, took out the element, installed new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from HAYDEN, AL
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cooktop burner was wore out from age
Just pulled the old cook top burner out and put the new one in .it took about 1 1/2 minutes
Was this instruction helpful to you?
Thank you for voting!