79061754103 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Elizabeth City, NC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was damaged
snap out the old one and snap in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelley from CLYDE, TX
- Parts Used:
- L304430992, 316048413
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old bowls were rusted beyond ability to clean
Put the new bowls under the stove top burners with disposable liners to protect them. They look very clean and shiny now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEWISTON, ME
- Parts Used:
- 316225001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken element
I followed instructions on your video. Took 10 minutes. My wife thought I was a pro.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Edina, MN
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large front burner would not come on under setting of "3"
Replaced infinite control very easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Florence, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burner was inconsistent the heating with red hot one minute and not the next minute
I watched the video on how to do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from New Castle, PA
- Parts Used:
- 318372211
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Burner element failed
Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MOUNT VERNON, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners constantly overheating, and inconsistent heating.
With the stove pulled out and unplugged, There are 4 square head screws to pull a metal plate off the back of the range. Once that is off, the infinite switches are in line and can be removed with a philips head screw driver/bit. I placed each wire onto the new switch as I removed them from the old, to avoid any confusion. The entire repair took less than 10 minutes. Incredibly easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from SANDY, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
burner switch failure
Unplugged the range. Removed the top section of the back of the stove to expose switches. Removed the knob, (pulls off exposing the 2 switch screws), unscrew & pull out from the back. The new switch was slightly bigger but the same manufacture and post letters & numbers. Transfer wires one-at-a-time from the old to the new switch. Mount the new switch back in place, put the screws in and the knob on. I plugged in the stove for a quick test, HA....works perfectly. Unplugged again and put the back panel back on, plugged back in and pushed the stove back in it's hole. BEFORE; the old switch when turned down would come back on BUT stay on high, a lot of boil overs. FINALLY: when turned on, it would NOT turn off, a real fire hazard. Thank you for having an original replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- adolfo from new york, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The element gets very even the control is at minimum
Removed the defective part. Install the new part, insert the connectors. Now its working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from UNION, OR
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replaced terminal block for element
followed the video provided on line which was very helpful..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lois from middletown, DE
- Parts Used:
- 5304506004
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
interior oven door glass cracked
All visible screws on sides & top of door, including screws for the door handle have to be removed. Fairly uncomplicated job, but as the glass that needed to be replaced, was 4th of 4 layers of glass, all needed to be removed from the outside in, in sequence, to get to the broken piece. Then as long as everything was apart, cleaned all pieces, before reassembling. Job much easier with two people, as one can hold & align all layers together, as the other tightens all the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from UNIONTOWN, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Switch quit working and wouldn't turn
Take handle off, then back cover. Of course unplug power. Switch wasn't built exactly like the original but all you have to do is connect each wire to the same letter, number code as on the old one . Works like brand new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERIC from INDIANAPOLIS, IN
- Parts Used:
- 5304506004
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken inside glass
Followed your video and it was not hard at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from W SAND LAKE, NY
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
8" burners were not responding correctly to the switches
Pull range away from the wall. Unplug range. Remove back plate covering the switches. Remove defective switch. Use bent paper clip to press center of terminal connectors and disconnect terminals. Reconnect each terminal of new switch as you go to avoid confusing terminals and connectors. Re-attach switch. Plug in range and test elements. Clean range area. Push range back into place, being sure to engage the anti-tip safety device.
Was this instruction helpful to you?
Thank you for voting!