79046123300 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Pearland, TX
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element had burned out
Extremely easy. Two screws and electric connection that had easy pop on-off connection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from addison, PA
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven not reheating after initial heat up
unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia from NEW BADEN, IL
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven Bake Element caught fire
Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phin from HARRISBURG, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The part I ordered has 5 connections and the part to be replaced has 7 connections. I had to ask a friend who is expert in electrical wiring to help.
My friend used a tester to determine where each wire was supposed to connect to. I'm not sure what he did with the extra connections.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rockie from KEIZER, OR
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
burnt out element
Followed instructions on website. Went perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Dayton, OH
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element burned out in my slide in range
Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from HIGH POINT, NC
- Parts Used:
- 318255006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Heating element broken
I followed the instructions from the lady taking my order she talked me through the steps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Coeur d'Alene, ID
- Parts Used:
- 318228310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lens was broken
after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oscar from Scranton, KS
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
F10 Error. Temp sensor at 1189 room temp ohms
1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from BELLEVUE, WA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Element burned out
The original instructions were to replace burner and plug wires back in the same plug they came from.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael A from Fairhaven, MA
- Parts Used:
- 318041603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replcement of inner door glass which had shattered
Removed the door from the range, disassembled the door, removed all broken glass fragments, installed the new glass, reassembled the door and reinstalled the door into the range. Straightforward and easy. Keep track of which screws go where and it is a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from MORGANTON, NC
- Parts Used:
- 318198817
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element not working
Open range door remove 2 screws on bottom of stove top remove top
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashley from CARRIERE, MS
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element in our drop-in oven stopped working
We turned off the power, took out the element, installed new element.
Was this instruction helpful to you?
Thank you for voting!