91195487991 Kenmore Range - Instructions

My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

really easy 2 screws inside the oven back wall holding the element then in the back of the stove disconnect two wires and pull the element through two holes .and place the new one into the oven through the two holes and connect the two wires . i turned on the power and i works perfect!

Isolated to control switch.

Replaced

verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you

removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in

Remove old, Installed new as per instructions.

The repair went very well. All parts were an exact fit. I was very impressed. I ordered the parts on a Tuesday and recieved them on Thursday with one rack backordered. On Friday the second rack was delivered. Very professional service. Thank-you.

There is not much to it!

Due to my disability, 2 neighbors came over with their tools. It took both of them to take oven door apart to install the new glass. All went well.

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.

Open oven door, unlock hinges and lift off. Lay on face on carpet or piece of cardboard. Remove 2 screws at top that go thru door and hold handle assembly. Remove 3 screws on bottom that hold bottom door trim to inner door. Carefully turn assembly over (hold it together so you don't drop the glass front!) and place back on floor, hinge side down. Lift off front glass and frame assembly. Lay flat on floor. Remove 4 screws that hold bottom door trim to side frames. If glass is stuck to bottom door trim (which it probably will be from rust and gunk)..... Remove 4 screws that hold side frames to upper handle assembly and completely lift glass and bottom trim out. Holding glass vertical, stand on the bottom trim piece and carfully work the glass up and out of the groove (do not wiggle it side to side or you will need to buy a new piece of glass). While you have everything apart, clean all the parts and remove the decade of gunk. Reassemble in reverse. The long screws at the top of the door that hold the upper handle assembly in place, have spacers around them, they thread onto the screws and maintain distance and alignment when re-assembling. Also, I found it easier to remove the handle from the upper piece (4 screws) to allow me to lay the whole assembly flat while screwing the bottom, side, and upper trim pieces together around the glass front. Once that is done, then put the handle back on before you assemble it to the inner oven door. That is it !

In order to replace the bottom trim (and side trims if needed) it is necessary to separate the oven door front panel and its outer glass from the inside door panel. It is best to remove the entire oven door and lay it down on a table in order to do this. (Refer to owner's manual for instructions on removing the door from the oven, but it basically lifts out easily when is is in the broil-open position). Remove the front panel of the oven door by unscrewing the two machine screws (these may be torx head screws on your appliance) on the top inside corners of the door that hold the door handle. (screw spacers on the inside likely will fall out when you remove the machine screws - don't be alarmed) Then remove the three screws at the bottom of door trim. The front panel can then be lifted away from the back panel. This will allow access to the screws that hold the bottom trim to the side trim. Remove these and the bottom trim will slide off. Replace trim pieces and reassemble.

Replace control switch