6654558992 Kenmore Range - Instructions

First I removed the two screws, then I pulled old element out, placed the new element in. Returned the screws in place. Very easy, cheaper to get online than anywhere else and was faster to get the part than anywhere else.

took two screws out pluged the new unit in and screwed it back on

On Saturday night before Thanksgiving my Wife indicated the oven was not heating up. A quick continuity check of the element indicated the unit was burnt out. I got on line and found PartSelect, found the proper element and ordered it. On Wednesday the element arrived and I removed the oven racks, removed two screws and pulled out the element to access the terminals. disconnected the wires, reconnected the wires to the new element and reinstalled the screws. Entire time was less than 5 minutes.

Thanksgiving dinner was saved at a reasonable price.

Unscrewed the two screws that held the old element to the back wall of the overn. Pulled out to reveal the two wires and connectors. Disconnected the two wires and removed old element being careful not to let the two wires recede back into the wall of the overn. Took the new element and connected the two wires. Then screwed the two screws through the holes in the element into the back wall. Easier than I thought it would be.

I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. It was that easy. But the people at PartSelect.com were the ones that made it easy; easy ordering and prompt shipment. I got he part in approximately three days. Thanks PartSelect.com. You made me and my wife very happy. We didn't think we were going to have the use of an oven for Christmas. You came through for us.

I removed the two screws that hold the element in place and then I pulled the element out and slid off the contacs and it was disconnected in less than two minutes. When it arrived I installed the new one the same way in less than 2 or 3 minutes and while I waited for thepart to arrive I got a chance to clean my oven and so all is well, I am very pleased with my purchase. It is just that easy and I am happily baking again. Thanks, j. Cale, morrow ga.

Turn power off, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new element, put screws back in and test.

simple replacement

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Removed the retaining plate screws (Phillips), pulled out the element enough to disconnect the wires, disconnected the wires. Installation was the reverse.

btw, PartSelect shipping was phenomenally fast. I ordered this part on Saturday and it was at my door at noon on Tuesday!! Holy Moly...

I order the part on 7/29 and much to my surprise, it arrived the very next day. It took less than 15 minutes to remove the old element and installed the new one. It was a little difficult to unplug the old one and took quite a bit of pulling but it came out okay. Plugging in the new one and screwing on the cover plate was easy.

Could not believe that the part was here the next day! Install was simple,just connect the wires and screw it in.

I ordered part from Part Select, which literally arrived in 2 days. I unscrewed the two (2) screws holding the old bake element in the oven. Pulled out the element and detached the wires connected to the element, which was easily done without any tools. Attached those wires (again easily by hand with no tools) to the new bake element and screwed the two (2) screws back in. The whole process including ordering the part online, unpacking the box and installing took 15 minutes. Wonderful and in time for my wife and daughter to bake Christmas cookies!

Well it was quite simple to replace all I used was a long Phillips screw driver,the job only took me 10 minutes to complete,thank you so much for the part you sent me it was the correct part.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.