79064090303 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Martinsburg, WV
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom bake element went bad
Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Spencer, IN
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Oven bake element was dead
Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.
Was this instruction helpful to you?
Thank you for voting!
Broken right side parts for lower over storage drawer.
Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from tulsa, OK
- Parts Used:
- L304430992, 316048413
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ugly looking drippans
in order to install the new burner pans, my husband used a screwdriver to push back on the metal clasp. this allows the notch on the drippan to go into the groove on the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Elkin, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element wouldn't heat.
The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevi from Verona, WI
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
heating element stopped working
All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Owensville, MO
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven lower element broke
Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Iowa City, IA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Element did not heat
After doing without the oven for a week or so we decided to turn to the internet and try doing the repair ourselves. We are not mechanically inclined/fix it yourself kind of people. This really was easy. Just detach the old element and attached the new one. A couple of bolts and snapping one out and then the new one in. Very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Gregory, MI
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The right Drawer Glide was broken.
The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bradenton, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Baking element burned out
Very simple, 2 screws, replace element, put screws back into place. The BEST thing... ordered on Tuesday afternoon, received on Wednesday afternoon, and Thursday was New Years day. This has been the best service, from any parts company, that I have ever ordered from. Keep up the good work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Aiken, SC
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Baking element burned out
The element went out on a Wednesday. We ordered the part the next day. We received it the following Tuesday (Mon. was a holiday). My 16 yr. old son replaced the part within 15 minutes. It was a piece of cake-actually it was a pizza!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed the two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed the two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from cartersville, GA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element burned up
removed two screws pulled element out about four to five inches attached wire to new element screwed back in less than ten minutes done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Ocala, FL
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
originaldrawer guide was cruched out of useable shape
first thing was to remove the crushed guide with pliers and a twist it was out. to install the new one islipped one side into the slot and took pliers and applied pressure on the lower glide into the slot; it was done presto. works like new. thanks,
Fred . it was so reasonable i got a spare.
Fred . it was so reasonable i got a spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven wouldn't heat
using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Browns Mills, NJ
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element broken
turn off power to oven at breaker box
remove screws holding bake element in
pulls wires off old element
put wires on new element
put the screws back in
turn the power back on
remove screws holding bake element in
pulls wires off old element
put wires on new element
put the screws back in
turn the power back on
Was this instruction helpful to you?
Thank you for voting!