79091106891 Kenmore Range - Instructions

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

Unplug range, remove top back panel. Remove knob. Replacement part is different, but if you look closely, each metal tab has a number stamped on the plastic housing directly beneth it. Remove old switch (2 screws)and remove and replace wires one at a time. You will need to cut the "one size fits all" metal shaft that the knob attaches to. We had to remove most of it, leaving only 2 "segments". File rough edges and apply vaseline so that the plastic sleeve will slip right on. We used the shorter sleeve (only 2 that are supplied will fit the knob). Replace unit and screw in. Replace knob.

It was a replace racks not repair. No problem

snapped the new piece of plastic in its place and ta da, its fixed.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

Pulled out the range, unplugged it and removed the upper back panel. The switches were held in place with two screws. Removed the old switches, detached the wires and plugged them into the new switches. Mounted the new switches, replaced the back panel, plugged the range back in and pushed it back into position. Appliance repair company wanted $370. I did it in 45 min. for less than $100.

Just took the old one out & put the new one in . Just a few screws to remove & put them back when replacing to new broil element , and were back up and cooking :)

Disconnect power supply,reemove upper back panel,pop otut old switch,disconnect it ,connect new switch ,snap in place ,screw uppper back panel back in place,reconnect range power supply.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I couldn't explain how to do the job any better than your instructional video does. As long as you follow the video instructions you should have no problems.

Simple Just plugged it in !

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson