36262781004 Kenmore Range - Instructions

I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

This one is a really easy fix as I only had to plug the burner element into the slot. I was very pleased with the speed of the order and would order again if I need parts.

Thanks,
Cheryl

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.

I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!

Difficulty was in determining the right model number and part number of a switch. Noted that the left front burner came on when the switch for the left back burner was turned on. By inspection I found the left front burner switch had become faulty by actually hearing an electric arc in the switch and smelling the oder in the switch. With help from the person I called I was able to determine that the Model Number on the actual stove was wrong. It had an extra 0 between the W and F which she said was a common error in the GE model number. I then gave the switch number I found on the switch to the contact person and she was able to verify the right part number. It was relatively easy to replace the switch by taking off the back upper plate then taking off two screws that held the switch to the stove. The part came quite quickly once ordered. Sears repair wanted $75 just to diagnose then the cost of the part. I got the switch for $69.

I had to remove the back panel on the stove to free up taped wires to get more length.

I couldn't tell which one work best till I installed 2 units and I liked the other bracket for stability.The wired were too long and there is not a given way to strap them and keep them away from the heat source.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

Pull stove out from the wall unplug it remove the old switches and replaced them withe new one. they work just fine.

After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.