1039858010 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from Orlando, FL
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Clips needed to re attach heating element
Pulled out old with pliers. Twisted new clips in per instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from fort mill, SC
- Parts Used:
- WB44M5
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broiler element burned out
shut off power to range, removed old element, looked up part on line, shopped for best price, Part select was $30 less than sears replacement part, ordered part, part arrived in 4 days, installed new part and I was broling again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Grass Valley, CA
- Parts Used:
- WB2X9146
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer guide
Used Phillips screw driver, installed guide, applied lubricant.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeeAnn from Clinton, MO
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lelia from Vienna, VA
- Parts Used:
- WB17X210
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner was unreliable...would stop working...I had already replaced the burner
I did as the video suggested.....I cut the old wires and spliced new ones already attached to the new terminal block. It would have been nice to have some instructions with the parts as I expected one piece but had to connect the wires to the new block and the new metal cover. I was guessing a bit. Also, I needed to use the holder strip off my old part so that it displaced the new part back far enough to insert the burner connections. That meant finding a screw and nut small enough to allow the metal cover to fit on the block. But the burner works great. I've learned that any repair requires some ingenuity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald L. from Cedaredge, CO
- Parts Used:
- WB17X210
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
the wires were not long enough to use the original path.
the original path was from the right front control knob around the back of the range and left side of range,which i dismantaled to install the new wires to the right front burner. When I found them to be to short I had to also dismantal the right side so the wires could be routed there. The new wires worked fine but did take some extra time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Eufaula, AL
- Parts Used:
- WB44M5
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burned Out Broil Element
The repair went ok. I did have to take the back off the stove in order to get to the wire connectors. Needed an extra person to move the stove out of it's location. Just had to be careful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Waukesha, WI
- Parts Used:
- WB2X9146
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drawer coming out of the track and falling to the floor.
pulled drawer out and installed drawer guide
Was this instruction helpful to you?
Thank you for voting!