91191461690 Kenmore Range - Instructions

I removed two small screws located on the underside of the control panel. I then rotated the bottom of the control panel up and dislodged the few connections at top back of control panel. The control panel became loose enough to lay forward exposing the inner control switches. The old problem switch wiring was removed one by one and placed in the same spot on the new switch. The old switch was then removed by pulling off the front control knob and then unscrewing two screws holding the old switch in place. Then the new switch was installed exactly as the old switch was removed.

Cut Wires to old terminal block and wired in new Terminal Block

Bent the tips so the phillament can fit inside the oven.

1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven

Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.

Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.

First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..

took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.

Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.

Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy

It was surprisingly simple. All I had to do was shut the breaker off to the stove(safety first). Next open the oven door and use a flashlight just to help you see,and unscrew the two screws holding the element in place on the back stove wall. Next slide the stove away from the was to give yourself enough room to access the back of it(you may need to unplug it to get it out far enough. My model had a cover over the back that took six easy to remove screws. Once the back cover was off I could easily see where the element was plugged into, so i removed the wires from the end of the element(just female terminals slipped over the end) i then went back to the front of the stove and pulled to element out.

To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple

I went by the video

Removed old broken element and installed new one. Took less than 10 minutes

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.