79096139400 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from BENTON, IL
- Parts Used:
- 316238201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The range element was not coming on
After settling that it was the Surface Element Switch, ordering and securing the switch, the first step was to disconnect the power to the Oven/Range. Next pull out the Range and remove the back and disconnect the switch from the top of the Range. Using the new switch I removed the wire connectors from the old switch and reconnected them to the new switch in the same spot that they came from. After connections were secure I reattached the switch to the back of the Range and reattached the back of the Range. When everything was back in place the power source was reconnected and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from WOOD LAKE, MN
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
NO HEAT IN UPPER ELEMENT
NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phin from HARRISBURG, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The part I ordered has 5 connections and the part to be replaced has 7 connections. I had to ask a friend who is expert in electrical wiring to help.
My friend used a tester to determine where each wire was supposed to connect to. I'm not sure what he did with the extra connections.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from BELLEVUE, WA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Element burned out
The original instructions were to replace burner and plug wires back in the same plug they came from.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from PACHECO, CA
- Parts Used:
- 316404002
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
wrong part received and returned
I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Colchester, CT
- Parts Used:
- 318178110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Element would not heat up
Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from GRAVOIS MILLS, MO
- Parts Used:
- 316407501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven coil twisted and cracked.
Found out it was easier taking the door off on you tube. Other than that it was pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- santa from glassboro, NJ
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temp was not reading right
remove back panel took out old part splice wire replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GLEN BURNIE, MD
- Parts Used:
- 316001002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The screw head was stripped and couldn't be extracted with a Phillips head screwdriver
If you do not intend to take apart the oven door to clean the interior glass, I would recommend you use a clamp to hold the handle and oven door tightly together while you replace the screw. There is a spacer between the back and front panels which could otherwise be shifted out of position. I used a screw extractor to remove the damaged screw and then installed the replacement. Wish all appliance repairs were this easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patti from Greer, SC
- Parts Used:
- 5304503232
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Cracked inside glass
I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma J from Riverview, FL
- Parts Used:
- 5304503232
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
inner glass door was broken
removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Collegeville, PA
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Door glass cracked
Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.
Was this instruction helpful to you?
Thank you for voting!