36272222203 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from The Villages, FL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
burners would not light
Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Woodstock, IL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Front burners had to be lit with lighter
My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Long Beach, NY
- Parts Used:
- WB13K10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
To Replace Gas And Burner Parts In Section 4
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela S from Chesterland, OH
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven Heating Too Hot, More Than 100 Degree Beyond Setting
Replaced the oven thermostat and calibrated the new thermostat by adjusting the temperature setting knob. Instruction I found on-line were very helpful and the repair was moderately difficult. Trickiest part was threading the new thermostat into the oven. Total repair time about 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from Waterloo, IA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Thermostat knob broke off
Cut off the power. unscrewed the cover. fed the new thermostat inside the over and rescrewed. Feeding the line was the most time consuming finding the hole to insert it in the back of the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Nashville, TN
- Parts Used:
- WB13K10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Large burner wasn't lighting very quickly
Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Irvine, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Alameda, CA
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
With the oven dial at OFF, the oven would turn on by itself every 5 to 10 minutes and it would heat up to about 100F and shut off.
Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Houston, TX
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace medium burner for gas cooktop
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Ft. Washington, PA
- Parts Used:
- WB02K10254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..
Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!