9114658816 Kenmore Range - Instructions

Remove oven door from hinges, by pulling it straight up and off, (like you would do for closer access to clean inside). Remove the storage drawer. Lift up and away off the track, (like a file cabinet drawer). With the drawer out and away, you can see how the springs are easily detached from each hinge. Note the location of where the springs attach to the hinges, and bottom of stove. Remove each spring. Three screws on each side hold the hinges on. Unscrew, and set them aside. (The new hinges did not have new screws in package.) Place new hinge in place. Reinstall in reverse of disassembly. If any part of the door or face of the stove (where hinges mount) was bent slightly due to forcing door open, reform with light hammer taps and C-clamps. Enjoy for ANOTHER 10+ years, because it's a GE Profile Stove : )

replaced lights in refrigirator and freezer

Called in and talked to someone and he look yup what he thought was correct but after i got them theywere wrong so i sent them back for a full refund minus 9.90 freight. I still need to figure out what i need for my 27 inch wall oven. Please help. Thanks

REMOVED DOOR TO OVEN
REMOVED HINGE [3 SCREWS]
REMOVED BOTTOM DRAW
UNHOOKED SPRING FROM LEFT SIDE ATTACHED TO HINGE
PULL OUT DEFECTIVE HINGE
REPLACE WITH NEW HINGE AND SCREWS
REHOOK SPRING TO HINGE & REPLACE DOOR
COMPLETE

FOLLOW VIDEO PROVIDED BY PARTS SELECT

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!

pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.

Lifted the door off the hinges, unhooked the spring from each hinge, unscrewed 3 Phillips head screws from the face plate of each hinge and removed the hinge assemblies . Hinges went in the way they came out; easy shmeasy. Took less than 15 minutes and the door is like new.

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

I knew the lens (which also holds the light) was broken. I also ordered the light. I flipped the circuit breaker, raised the stove top and removed the 6 nut-head screws holding the cover plate. A nut driver would have been helpful, but I got by with a 6" crescent wrench. I removed the cover. I unplugged the two wires from the old light and plugged in the new one. I inserted the new lens and slipped the light over it. I flipped the circuit breaker on to make sure it worked. After flipping the circuit breaker off, I replaced the cover plates and the screws and lowered the stove top. I flipped the circuit breaker on. It worked!

Real simple. Disengaged springs at the inside bottom, replaced hinges and reengaged springs.

The customer service rep was brilliant in finding the
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you

repair went fine, real easy.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

After tilting the oven door out and sliding it up to remove it, I slid the storage drawer our completely from the range. After removing the spring that held the hinge assembly under tension, I removed 3 phillips head screws that held the existing assembly in place and removed it. After verifying the part you sent was an exact match, I reinstalled the new part, fastened the screws, attached the tension spring, installed the storage drawer, and then slid the oven door back in place on the brackets, completing the repair.