91193581991 Kenmore Range - Instructions

First turn off the breaker, and test with my milti meter. Raise the top panel where the coils are and prop it open high enough to use a screwdriver to open the front panel.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

I removed the door by unclipping the hinges with a screwdriver - very easy. I laid the door on the kitchen island unit on the polystryrene packaging. I removed all of the star bolts. I need not have removed the star bolts around the door hinges as these hold the hinges to the inner frame. The cracked double glazed unit lifted out and was replaced very easily. We took the opportunity to clean all of the parts that don't usually get cleaned - hence the time taken. Reassembly and reattaching the door was very easy. We didn't rush and were very careful in laying the door on a good flat surface. The oven is now good as new. Well done PartSelect for stocking such an old part - $125 to keep the range working perfectly.

I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.

Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !

Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!

I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.

ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.

First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.

Replaced element control switches

Put the two leads in in and bolt it back in the oven

Pulled the stove out from between the cabinets, used a blade screwdriver to pop the oven door retainers down and lifted the oven door out, removed the racks. used a 1/4'' nut driver to remove the 5 screws holding the broiler in place. From the time I unplugged the stove from the outlet until I plugged the stove back in was 15 min. I would suggest wearing gloves because the metal frame around the burner element has sharp edges.

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .