79092313300 Kenmore Range - Instructions

First I unplug the stove and then started to take off the back panel off behind the stove. Then I took the relay panel off by taking the four screws, that holds the relay in place. Now it took me a few minutes to unplug the wires
from the relay panel. Let me tell you that these wires were
really hard to pull off the relay. After a few minutes later
then I started to put the new relay panel back on. The wires were easy to put back on the new relay. Then I put the back panel back on and then plug the stove back in. After that the power was back on and the new panel fixed my issue.

Used a nut driver to take off upper silver back off. Took one wire off at a time and rewired new timer. Used same nut driver to remove old timer,stuck on old cover on new timer and screwed it it. Rescrewed back on, plugged it in and it works great.

I google parts for my oven and I found you all. I read a couple of your other stories and I see I wasn't the only one that ran into this problem before so I took there advice and the part was a my home in three day I pit it in and it is working now thanks

I removed the drawer, removed and replaced the guides on both sides in the front and replaced the drawer.

Just use flat screwdriver to press on clip and just squeeze it in

After researching on what exactly to call the part, which was a front drawer glide. I found this out by watching the video. It showed me exactly what I needed and what it looked like. I run to the oven to look at the other one, to make sure thats what I needed, and it looked like the part that I needed (mind you I am a female, and not a repair person), so this video helped me out alot. When the part arrived, I knew how to take the drawer out, and easily snapped the little plastic glide in to place, and slipped the drawer back on the gliders, and it worked perfect, so proud of myself, that I done it by myself, with no help from husband. I bragged and bragged on myself with a big pat on my own back, thanks Part Select, I know what to do when it happens again. Its my fault cause it broke, cause I overload the drawer with pots and pans LOL!!! Brenda Dixon

Removed the drawer. Inserted the new glide tab into a hole in the side. Inserted the drawer slides in the the glide. Closed drawer--done! Works fine. Probably only 5-10 minutes.

The drawer under the oven had been aggravating me for some time. It was titled and did not close right. Finally, I took it out to see what the problem was and noticed that the glides were broken. I googled the model no. of the stove (figuring I would have no luck) and to my great relief was directed to this EXCELLENT site. I ordered the new drawer glides within minutes and they were literally delivered the next day. Snapped right in, fixed, happy!! It's times like this when I can't figure out how we all lived without the internet!

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

replaced it

First i removed the drawer. Then i removed the broken drawer glide and replaced it with the new one. Then i put the drawer back! The parts were a perfect match...

No problem..... I just had to slide the new one in..It took all of 5 minutes...
I searched so many different places for the part until a friend told me about Part Select!!!
Thank you so much...

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

We have an older .......range that came with our house when we bought it in 2000...the stove works fine (for an electric stove!), but the drawer was always problematic. Sometimes it would sit straight in the appliance cabinet and sometimes it wouldn’t. Sometimes it would flop up and down, sometimes it worked and sometimes it didn’t!

We lived with it for TEN years...then a couple of weeks ago I needed a pizza pan. I opened the drawer and the darned thing wouldn’t go back into the stove properly. I played with it for awhile, trying to figure out why it didn’t work correctly! After some energetic observation (accompanied by some choice words about American engineering!) I realized the front drawer guide was broken off!! It was one of those “Aha!” moments!!

I retrieved the plastic piece and went to a local appliance store to get a replacement. They said they’d order one (for 8.95 and I pay shipping and handling!), and it would take 2 to 3 weeks to get it! I declined their offer. Surely, somwhere on the internet there was a supplier who had this part!!

I sat down with my MacBook Pro and looked up “range parts” and was immediately directed to partselect.com. I looked up the part (which was ONLY $3.38) and ordered two. I had the parts in my hand in four days, and even with shipping paid less than half what the other place wanted locally.

I pulled the drawer out, literally dropped in the new guide, and the drawer has worked flawlessly since!! We are forever grateful for PartSelect and will always keep their address on top of our web vendors list!!

Give them a chance...the least you could do is save some aggravation, and maybe a little bit of money, too!!

Ge wanted over a hundred dollars for the same part you charged only $80. Thanks. I'll be buying again.