9117398790 Kenmore Range - Instructions

Remove the broiler pan to get at the 2 nuts that hold the gas burner, remove them and then you can get at the 2 nuts on the back side of the igniter.

This web site is awesome!!! their forum told me what part i needed, and they shipped it out, super fast, i couldn't hardly believe it! I tried using the Sears Parts web site for my "kenmore" oven and that was a joke, seriously! no more kenmore for me, thanks. It took this site to figure out that i really had a G.E. with a kenmore name on it.
I found out that even though the old ignitor glows well, it may not pull enough amps to open the gas valve.
First i disconnected the two wires on the gas safety valve that lead to the ignitor. These are accessed after taking the bottom drawer out. Then using a nut driver, i took out the two screws holding the bottom of the burner tube. Then inside the oven, i took out the racks and then the two screws in the back on the bottom. Then took out the bottom plate. I removed the one screw on the front of the burner tube, and removed the burner tube with the ignitor attached. I cut the wires off the old ignitor and attached them to the new ignitor with the supplied ceramic wire nuts. I attached the new ignitor to the burner tube and put everything back together. The bottom screws on the burner tube were very difficult for me to reach. Almost impossible to get both hands there to do the job.

My repair was easy. The hardest part was trying to get the 2 small screws off and on the igniter. You need small hands or a small, angled socket set. I did mine with the door of my oven still on and maybe that was why I couldn't reach the screws that well. If you can do the repair with the door off, I would say that would be easier. As soon as the new piece was screwed in, it worked on the first try.

removed oven door, removed drawer under oven, removed three screws holding hinge assembly, unhooked spring from hinge arm, inserted new hinge arm, attached spring, positioned hinge assembly and replaced screws, reinstalled drawer beneath oven being certain that no pot handles interfere with the hinge spring loaded arm, reinstall oven door.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas into the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.

The repair went surprisingly well! My only problem was the bottom screws needed WD40 to loosen, but otherwise the parts went in easily.

i went for 3 months waiting on the electrician who never came then asked the plumber who else could fix it and he said my husband could it only needed to unscrew 4 tiny screws and unplug and cut and twist wires back the hardest part was reaching the bolts hooked to the ignighter the burner was in the way and is not as easy to remove as someone has said all in all it saved us 100 dollars and could have saved us months of burning food trying to cook on broil if i had only called the plumber first.ha ha

It was a simple repair removed the oven door, and the oven bottom plate. removed the screw that held the burner tube to gain access to the two screws that hold the igniter in place clipped the wires. put the new one on with butt end wire connectors instead of the wire nuts supplied. screwed the igniter back onto the burner tube put the burner tube back in place and secured it with the screw, replace oven bottom and door the whole repair took 20 minutes.

IThe schematics on the website were helpful for how everything goes together. I just followed the picture and then unscrewed all the screws that held the ignitor to the gas pipe. Have to pull out the gas pipe out first so you can get to the bolts, easy to do when you pull out the drawer and unscrew the hold down for the gas pipe.

No directions came with the part, and the length of the new wires weren't long enough nor did they have the attachment pieces that are needed to plug in the wires. However, helpful tips from others on the website told me that you have to cut the wires off the old part and screw the wires from the old to the new with the white plastic wire couplings. Worked like a charm!

It was a simple procedure, and I saved myself buying a new stove or paying someone else to fix it!

Slid off the oven door and loosened the hinge assembly. Removed the storage drawer to unhook the spring and then took off the old hinge assembly.

Inserted the spring into the new hinge assembly and then installed it - just tightened the screws. Hooked the spring into the lower point. Slid in the oven door and tested it so that is opened/closed easily. Cleaned under the oven while the storage drawer was out.

We can now bake bread, pizza, etc. What a relief.

I rempved the top and bottom doors, than the wire rackes followed by the bottom base of the oven. Then I removed the burner cover plate so I could get to the igniter.. I removed the cover plate for the wiring (2 wires), unpluged them, removed the igniter (2 screws). I had to cut the wires on the old igniter and couple the ends to the new igniter and then replaced everything by just reversing all that I did. Simple! Easy!

Assumed this broken hinge was going to be an expensive service call. Decided to try and fix it myself. Ordered the part off partselect.com and got some repair tips off the website that made this a breeze. I am not handy at all but was able to complete the replacement in less than 30 minutes and spent only $30 on the part. Just needed to unscrew the old hinge and release the spring from under the stove (which I accessed by pulling out the drawer). It would have cost me over $100 to just get a service person to look at it.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...

I really do not have the time to do this right now, however, I feel that it is important to tell everyone that dealing with PartSelect allowed me to repair the stove and please my wife in the easiest way possible. I will use PartSelect forever....

i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!