9117838610 Kenmore Range - Instructions

i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!

Go to utube videos for this are there

First shut down electric power to oven. remove
oven racks and botton tray. Removed boiler rack and door. Next unscrew 2 bolts holding igniter. remove nuts or cap for two white electric wires.
installed new igniter, hooked backup wires. replaces racks and tray and that was it, job done.

This web site is awesome!!! their forum told me what part i needed, and they shipped it out, super fast, i couldn't hardly believe it! I tried using the Sears Parts web site for my "kenmore" oven and that was a joke, seriously! no more kenmore for me, thanks. It took this site to figure out that i really had a G.E. with a kenmore name on it.
I found out that even though the old ignitor glows well, it may not pull enough amps to open the gas valve.
First i disconnected the two wires on the gas safety valve that lead to the ignitor. These are accessed after taking the bottom drawer out. Then using a nut driver, i took out the two screws holding the bottom of the burner tube. Then inside the oven, i took out the racks and then the two screws in the back on the bottom. Then took out the bottom plate. I removed the one screw on the front of the burner tube, and removed the burner tube with the ignitor attached. I cut the wires off the old ignitor and attached them to the new ignitor with the supplied ceramic wire nuts. I attached the new ignitor to the burner tube and put everything back together. The bottom screws on the burner tube were very difficult for me to reach. Almost impossible to get both hands there to do the job.

Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cover off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

The spark control module is located in the top section near the clock. Take off the back cover. Use needle nose pliers to disconnect the wires. The modules are marked with letters so connecting the new module is very easy. The range works great. My Kenmore is a 1985 model.

Straight forward as per instructions. Removed old igniter, replaced and tested new one and it worked. However, the gas oven would not turn of. Valve may be defective. Knob control is not stripped and turned to full stop. Troubleshooting continues. Part(s) and instructions worked perfectly.

1. I have searched info on the internet and found that site.
2. Initially I could not figure out how to unscrew ingniter. After reading more post I have found out how to access nuts underneath.
3. After I have removed lower drawer and unscrewed metal cover and then inginter nuts.
4. I have got a part with two wires attached to the igniter and two porcelan insulator, so it was very easy to cut old wires and connect with an igniter wires in parallel

/||\
||

First i removed the inside bottom of the oven where i could get to the actual glow plug igniter and removed the two screw that held the igniter in place. I than pulled the entire oven out allowing me to access the two wires connecting the igniter to the stove. I disconnected the wires and had to splice the wires as to be able to reach the appropriate connections. I reinstalled the igniter and upon testing the igniter worked properly. The entire process took me one hour.

Followed suggestions of previous posts. Removed oven door, warming drawer, pan in bottom of oven. Removed element to replace igniter. One thing I would add is I put a small piece of electical tape on the heads of the two 1/4 in. screws for the rear element bracket. This kept them from falling out of nutdriver.

Following the recommendations of others I decided to attempt repairing the oven by myself. I unplugged the stove. I removed the oven door, the drawer, the drip pan from below the oven unit and the oven pan to access the igniter bracket. All screws were 1/4" hex head except the oven pan which were slotted. I disconnected the 2 wires. I removed the old igniter and cut the 2 wires close to the old igniter to allow extra length to splice to the new igniter. The new unit included 2 wire-nuts. It was simple to wire-nut the new wires to the old ones and install the new igniter. I reassembled the pans I had removed and the door. I plugged the stove back into the wall. The new igniter worked perfectly. My wife continues to tell me how great it is to have a working oven again and how much faster it seems to heat. I am thankful the oven didn't fail while we were cooking the Thanksgiving turkey the week before. I debated calling a repair technician or shopping for a new stove. The price of the new igniter and the description of the procedure convinced me to attempt a repair. I am very pleased with the results.

removed bottom of oven.removed heat shield.i
then unscrewed the wire nuts to the igniter.i
then tookout the burnner with the igniter attached.
i unscrewed the two screws holding the igniter
in place,and put the new one on.i then screwed
the wire nuts back on,and put it back togather.
it works great,thanks for the help.it saved me alot
of money.

Checked on this website for ideas. A 20+ year repairman posted that the problem is the control valve and I should replace the igniter while I'm there. The valve was priced at $189 and the igniter $60. I decided to try the igniter first and all is well. Valve not needed.
Steps; remove; door, lower tray, and oven floor pan. Disconnect two igniter wires. Use 6mm sock to loosen gas feed tube, then lift tube up a couple of inches to access igniter screws. Remove them, and reverse process with new part. I tried to R&R the igniter without loosening the gas feed tube but it's a real PITA. Good luck, easy fix.

Diagnosed the problem as igniter failure and called local parts outlet. They gave me the part number, but said they were out and directed me to another vendor. When the part came, it was the wrong shape but I tried it anyway. Result - the igniter glowed which allowed the gas to flow, but igniter, being the WRONG PART, didn't ignite the gas, allowing a dangerous build-up of gas.

I then went to PartSelect, looked up the part, saw it was the correct one, ordered it (arrived within 3 days) and, because I already had the pans and covers off the oven, it was a matter of minutes to install. Works like a charm and, though I usually like to buy locally, I'll check out PartSelect first next time!