91146244896 Kenmore Range - Instructions

Removed two scres that hold element in Place. Pulled out element about 3" and removed wire disconnect. Re-connected new element and re-installed mounting screws. Very easy. Parts were delivered promptly. Great service!!!! Thank you Parts select!!!!! Saved me a trip to Sears to purchas a new element or Stove.

I read the "easy to repair" story after I ordered my part and I felt like I coud do this on my own. (Female not much experience in repairs) I shut off circuit breaker...proceeded to take out element...could not get it to easiler come off...so I made the mistake of cutting the wire because it looked like that's what I needed to do. WORD TO THE WISE...there are clamps that actually pull off the element..just need to pull a little. So my "easy" project was made more difficult because I didn't know this up front. Otherwise it would have been a breeze. I had to go to the hardware store and but new clamps and attach to the cut wire. Good news is my oven is now working and Parts.com was fast, cheaper than the GE parts place and great service.

pulled stove out from wall about a foot ans disconnected the electricity cord. removed the 2 screws holding the element in place and pulled it out a bout 3 inches and disconnected the two wires. attached the new element & pushed it in place and tighrened the 2 screws. hooked up the electric power, moved stove back in place & it was done!

Turned off circuit breaker for Range. Removed the 2 screws holding element and pulled wires attached to the element through holes. Disconnected the wires and attached new element. Had problem with one wire springing back into hole used paper clip to fish it back out of hole and then connected 2nd wire to heating element. Turned breaker back on and tested. Baked a cake. MMMMMMMM.

the only challenging thing realizing that the screws in the back weren't for a screw driver, they were for a very small wrench. Since I didn't have such a tool, I just used vice grips. It all went well though. The oven currently heats to 400 degrees in 7.5 min. I am quite happy.

1. Turned breaker to the oven to the off position.
2. Removed screws from back of oven-This was the most difficult part of the entire process!
3. Pull out element about 3", then tugged a little harder to expose the wiring.
4. Unhooked wiring from element.
All of this took about 15 minutes.
When new one arrived (less than 48 hours), I did the reverse of the above. This took about 6 minutes replace with new element. Thanks so much!

Piece of cake. Pulled range out, unplugged it, opened stove, unscrewed element from back of stove w/ socket wrench, pulled out 1/2 way, unplugged bad bake element from the 2 wires, plugged in new bake element in, reattached to back of oven, plugged in stove and it worked.

Remove two screws holding element. Pull element forward exposing connections. Pull connections apart. Replace with new element. replace screws. Done

Removed the two screws and pulled out the bake element. Then plugged in the new element and replaced the screw. Easy

removed two screws, pulled element out (which broke at the sparking site) Took screw driver to push off where the element was connected. Put new one in, re-did screws. Turned on and off oven. This company was great to work with, smooth sailing. It was funny when we noticed the problem-Husband said $125.00 repair, I got on net and said no about $40. He is taking me out to dinner tonight.

Removed the two screws pulled out the old element and slid the new element in and put the screws back in. I used it that night to bake supper

As others have described, the removal of the old bake element is easy, just undo screws in the mount holding it to the inside wall of oven and pull out, then disconnect wires.

The first thing I faced unique is that some of the old element melted on the walls of my oven. After scrubbing extensively, it was obvious that the majority of the melted element was permanently fused with the oven wall--although it doesn't seem to have affected oven performance so far.

Next since my range was made in 1982, the replacement bake element didn't exactly fit my unit. Several adjustments had to be made. The size and fuctionality of the new bake element matched my oven, however the wire connections and the oven wall mounting bracket and the spacing of the two ends of the element as it went thru the oven wall were very different and required extensive modifications.

I used the old mounting bracket from the old melted element to attach the new element since my oven wall opening and mounting holes matched the old element mount--NOT the new element mount. This required removing the old mount from the old element by means of a vice, hacksaw and wirecutters. It was necessary to examine the old element mount very carefully before I hacksawed it off the old element as it must be reconfigured onto the new element. It will be bent up somewhat while removing---be careful.

Then I reattached the old mount on the new element. This required carefully bending the new element ends to receive the old mount as they were spread too far apart in the new element configuration. After much trial and error bending with several types of wirecutters the old mount was secured to the new element and installed into the oven.

Now a new problem appeared--the element ends now stuck too far into the back wall of the oven, making them dangerously close to touching the exterior of the rear of the oven and remember these are bare, hot electric connections! Much time in trial bendings and repositioning of the new element with the old mount finally resulted in a successful mounting with the old mount and the new element in a way that safely kept the bare wire connections within the rear oven walls.

A final problem was encountered when the new element came with slide-on wire connectors while my old element had screws and holes to connect the wires together. I found a drill bit the size of the required screws and drilled holes in the new element's wire slide-on connectors so that I could use the screw connector system of my old element to connect my new element's wires together. It all worked and the oven is functional.

This was really easy considering what it would have cost to have a repair person come and do it - not to mention the wait time. I had to hunt around a little bit to find the right socket, but once I had that, I unscrewed the bolts in the back and slide the element out. TIP: make sure you turn off the electricity!!!!!!!!! The wires were a little stuck, but the oven is 11 years old, so it's to be expected. One of the wires came off behind the oven, but I used needle nose pliers and fished around until I grabbed it. I detached the wires, attached the new ones, turned the electricity on and it's been baking Christmas cookies ever since. BTW - the part came in 3 days. I was sooo happy I didn't have to wait for a repair person. Thanks for all of you who posted your comments online. That was just the encouragement I needed to try it myself!

Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)

I had grease on the baking element when I turned the oven on. I thought it would burn off, it caught fire and destroyed the baking element. I ordered a new element, it came within two days. I didn't wait for my husband to come home. I got a screw driver, took off the screw, used pliers to pull apart the old baking element from the wires. I did this carefully , our oven is old and the element was not pulling away easily. I inserted the new element, put the screws in and it worked perfectly! I was very proud of myself but the truth is that this is a simple job.