3636244190 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Wetumpka, AL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Oven would not heat up
Took out the hexagon screws, used pliers to pull the connecting ends apart, slid in the new element in to the connecting slots, reattached to screws, turned on the oven to see if it would heat up and it did. It was really easy. I had waited for a week to get the part from my local Sears parts house. You sent it out and I had it in 3 days. They still don't have the part. Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Charlotte, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom element cracked/split - open circuit
Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & since I was so tired from all of this 5-minute activity, I rested.
Al S.
Al S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Newnan, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Defective
Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using original screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Plano, TX
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
botton bake element burned out
Removed to screws holding the bake element in place. pulled out element to get to the 2 electrical connectors. removed connectors from old unit. connected new unit and secured with the screwes. very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from Prosser, WA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
For some time our oven had been working eratically, temperature spikes and drops during baking process. I thought the thermostat was the problem. The last time baking, element sparked and overheated in one spot so we removed the element. It was warped and cracked. We replaced it with the new ele
I removed the two screws with a nut driver, pulled the element out far enough to expose the connection point and disconnected the electrical clips. Upon receipt of the new element I did those things in reverse order and it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Carmichael, CA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Burned out element
Turned off circuit breaker, removed the two screws, pulled out the wires, unhooked the connections and hooked up the new element. Put the two screws back in, turned on the power and it worked! So, so easy! I wouldn't have attempted it had it not been for the other stories associated with the part I purchased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from east stroudsburg, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
coil burned out
replace coil 2 clips off 2 clips on........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Barnesville, OH
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake element burnt apart
I removed the 2 screwws inside the oven cavity and pulled the element towards me. I unplugged the wires from the element and plugged in the new one and secured it in place with the 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvard Folding Box Co from Lynn, MA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken bake element
Shut off electrical supply to stove.Remove 2 screws.
Slide element out enough to remove connectors from element.
Position new element.Slide connectors onto new element.
Slide element back into position.Replace 2 screws.Turn on electrical supply.
Slide element out enough to remove connectors from element.
Position new element.Slide connectors onto new element.
Slide element back into position.Replace 2 screws.Turn on electrical supply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Bivalve, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Heating element worn-out
Turned off the breaker to the stove, removed oven racks, used small pair of plyers to remove bolts (2) holding defective element in place. Pulled (2) wires that had a snap connection apart. Old element was not removed. Connected (2) snap wires, pushed them back into the oven wall, used plyers to re-connect the element to oven. Installation DONE!
Turned on breaker and then the oven; we are now baking again.
Turned on breaker and then the oven; we are now baking again.
Was this instruction helpful to you?
Thank you for voting!
Blackened and rusted drip bowls on range.
Pulled out heating elements, removed old drip bowls, replaced with new drip bowls, re-connected heating elements. Done! Looks like a new stove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joey from barto, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bake element had broke and caught fire
It was real easy all I had to do was turn the breaker off,Undo two srews and disconnect the two wires. Then repeated the process to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Matthews, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Old element shorted out after Thanksgiving (thankfully)
We were able to purchase the part and replace it for under $25. We took off the oven door and installed the new element in under 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Columbia, IL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element burnt through
Very easy repair. Part came wrong the first time (my fault for ordering the wrong one). Called and ordered the correct one after a closer match to the original part. Delivered much quicker than promised (one day) and installation very easy. Will use this site for all future repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joy from Leesburg, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven Bake element broken
Well...you'll notice in other tools I put Tweezers. Now you really don't need tweezers if you do it right in the first place. Here's what I did: 1) unscrewed the nuts that hold the element in on the back of the unit. 2) Then pulled the terminals out of the holes in the back of the oven. OOPS...there were sparks as the right terminal wire hit the metal frame of the back of the oven. Scared me. I jumped. the terminal wire burned/broke off and fell back into the hole. Yep...Too late I remembered that the VERY first step of this repair is 1)CUT OFF THE POWER TO THE OVEN. I repeat...THE FIRST STEP IS TO CUT OFF THE POWER TO THE OVEN. I couldn't reach the wire with the needle nose pliers so I had to go get the tweezers. Couldn't see the wire but I just put the tweezers in about two times and it finally caught on the wire and I was able to pull it out. Luckily the terminal end was still connected to the wire so I didn't have to replace it. From there it was 3)remove the old terminal posts from the wires (used the needle nose here to wiggle the ends off - been on a long time), 4)insert the new ones, 5) push the terminal posts back in the holes, 6) screw the nuts back on, 7) bake the cornbread. A very quick job -- plus the element from PartSelect was almost half the price of any other I found (due to this I was able to upgrade the shipping a little to get it sooner and still saved money over any other price I found. Just remember to CUT OFF THE JUICE BEFORE YOU START this repair and it will be done in 5 mins or less.
Was this instruction helpful to you?
Thank you for voting!