36272285890 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Willie from Selma, AL
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The oven door gasket was worn and didn't provide a good seal.
I use needle nose pliers to remove the old gasket tabs and clean the area with a scouring pad. Then I just lined the gasket up with the holes on the door and pushed the holding tab into the holds.Very easy and simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lincoln, CA
- Parts Used:
- WB07K10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End cap cracked. Tried to fix it with epoxy, but it didn't work.
Used screwdriver w/star bit to remove two screws (longer one on top). Removed cracked end cap. Placed new end cap into position, making sure all tabs were correctly aligned. Replaced screws (top one first)tightening them slowly & alternating back & forth so as not to crack the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from The Villages, FL
- Parts Used:
- WB48T10095, WB49K2, WB48K2
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The problem was the oven rack and broiler pan was missing when we bought the house,
I carefully opened the oven door and slid the rack into the groove taking great care not to dislodge the heating element nor to burn myself on the cold oven door. I then pulled open the drawer on the oven and, again, with great care placed the broiler pan into the drawer and slid the drawer closed, again taking great pains to make sure I did not burn myself on the cold over. The reason for the length of repair time is I did not open the box for 2 days. Thanks for the laugh!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnette from Baltimore, MD
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no racks to oven
Easily glide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from battle mountian, NV
- Parts Used:
- WB48T10095, WB49K2, WB48K2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing parts
placed them in propper position we had been to apliance stores and told they would need to order them and it may take up to two weeks to get them. we ordered them from you and they were here in a matter of days, and the price was the best we had been quoted. thank you so much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AL from PHILADELPHIA, PA
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
broken left /right range lines broke off
loosen the compression fitting both ends and screwed new ones in place .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUNSOO from NORTHBROOK, IL
- Parts Used:
- WB28K10024
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Cracked the left burner tubes
I opened cook top without disassemble cook top and broke the left front tube.
After I received left front tube and disassemble cook top to install and found right front tube also not good condition.
I ordered right front tube and installed both tube. I recommend order both front tubes to save shipping.
The tubes were easy to install but little bit hard to remove old Electrode for disassemble cook top and to line up cook top and holder orifice screw hole for assemble.
After I received left front tube and disassemble cook top to install and found right front tube also not good condition.
I ordered right front tube and installed both tube. I recommend order both front tubes to save shipping.
The tubes were easy to install but little bit hard to remove old Electrode for disassemble cook top and to line up cook top and holder orifice screw hole for assemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Las Vegas, NV
- Parts Used:
- WB27T10469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no display
Turned off circuit breaker to stove, remove top panel and then the old control module and installed replacement. Power back on and top panel reinstalled. Easy!!! And Everything works like new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Alameda, CA
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
With the oven dial at OFF, the oven would turn on by itself every 5 to 10 minutes and it would heat up to about 100F and shut off.
Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Lorain, OH
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
only back burnners lit
Rremoved the back cover, changed the wires from one ignighter to the other, removed the old ignighter, and snapped in the new one, put four screws back on cover, and pushed stove back into place, turned on all burners several times to make shure eveything worked!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRICIA from INGLESIDE, IL
- Parts Used:
- WB16K10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Igniter was getting red hot but was not starting burner!
Very easy repair! Removed lower oven pan/ plate. Removed burner tube with 3 screws, removed igniter and reversed to reinstall!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from New Milford, CT
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The front tubing broke.
The parts were easy to locate on the website, reasonably priced, and arrived in two days. The installation was simple and the parts fit exactly as they should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Blairsville, GA
- Parts Used:
- WB29K10004, WB18X21511
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing burners and burner caps
I bought a used gas stove for canning for $25.00. I spent about an hour cleaning it up. It was missing two burners and burner caps, which I replaced. So, for $110.00 I have a practically new gas stove.
Was this instruction helpful to you?
Thank you for voting!