79092854302 Kenmore Range - Instructions

Quit after getting shocked. New part had different configuration. Hard to see marking for pull and plug from old switch to new switch. New switch had different configuration. After all that and making sure switch worked, got shocked as stove was pushed back to wall. Some other issues with wiring has a shorting out problem. Maybe time to call a pro or get rid of the stove and get the gas stove we have been longing for. Be sure to match points on pulling and plugging as the configuration may be different.

Unplug the range, pull the knob off the front. Remove the screws from the cover plate behind the switch and remove the cover plate. Carefully pull one wire at a time off of the old switch noting the markings: "L1," "L2," "H1," etc., as the wire position may be different on the new switch. Put each wire onto the new switch as they are removed from the old one. Let the new switch hang from the wires while removing the 2 Phillips head screws from the front of the old switch and remove the switch. Hold the new one in place, start both screws, & then tighten them. Push the knob on the new switch. Plug the range in and try it. If everything works, install the rear panel and screws. I think that it took me longer to type this than it did to actually do the job.

After making sure it was the switches themselves not the burners that were the problem, it was easy locating the exact parts I needed on PartSelect and the shipment arrived in a timely manner. I had to replace two out of four switches. Using a screwdriver, I detached the display pannel and removed the faulty switches. Then I disconnected the old wires and attached them to the new switches, one at a time. Closed everything up and the "new" range works great!

Unplugged the main cord to the socket in behind range. Took back panel off. Unscrewed switch from its position on face of range. Switch is not a look alike switch to original, so had to pay attention to the labeling on both switches as to their identity. Removed one line at a time from old switch and placed on new switch. Rechecked positions of the wires and made sure there was no binding of the wire positions when installed. Mounted switch to same position previous switch was removed. Reinstalled back panel, plugged in range and tested switch. Very easy repair as long as you can see the labeling on back of switches. I used a light having a strap that is positioned on my head for best lighting possible for one person repair.

I ordered the exact replacement element, and after unpacking it, it took about 5 minutes (actually,less; didn't time it), and the new element was installed and working fine.Thank you very much.

Moved range foward, unplugged it,removed upper back cover(5 screws)replaced corresponding switch.(make sure to disconnet one wire at a time off the old one and connect to new one so you get them right)attached switch to range by screwing the 2 screws that go in the front and pushed in control knob.Also replaced burner by pulling out old one and plugging in the new one.Plugged in range and moved back into place.Made sure it worked right and done.Very easy fix!

Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

Took old one out and plugged the new one into place.

So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....

Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.

I ordered the element. When it arrived, I simply removed the old one and put in the new one. However, it did not completely solve the problem. The heat is now distributed evenly, but still have to turn the burner to 7.5 to boil water.

removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.

Touch up paint was easy to apply. I gave it a few coats and you cannot tell where to chip was. I wish you had a standard mail delivery option. I paid twice the price of the paint for fed ex delivery. I didn, t need the paint next day but it did get here before the estimated deliverydatee.

Removed the old oven racks and put in the new ones.