66592015102 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kristine from Drexel Hill, PA
- Parts Used:
- WP8053834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I shattered the original one when I took it out to clean it.
I placed the new glass in place, and replaced the screws. What I really want to tell abut is how QUICKLY my replacement part came from your company. I was so upset when I broke the original glass, but the replacement glass arrived within 24 hours! It was wonderful! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Negaunee, MI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from windsor, VA
- Parts Used:
- WP3148952
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
water pump went out
it was very easy i took the pump off only two clips and two hoses holding it type in the model number at parts select it came right up soi new it right one from the picture got with in 3 days put it back on less then 10 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Weston, WI
- Parts Used:
- WPW10308477
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
lower element burned out
So easy. Unplug the range. (really important. You're working with wiring after all) Unscrew the metal plate holding the bake element in place, gently pull out the wires and detach the element from them. (the element just pulls off, but it was attached pretty tightly so I did have to use needlenose pliers to get a better grip on it.) Then simply plug in the new bake element, push the wires back in, reattach the metal plate and bake a cake! Don't even think about calling a repairman for this one! It took under 10 minutes once I got around to ordering the element. (none of the local stores carried them)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnne from Harrison, AR
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven element burnt out
unscrew two screws..took old element out, put perfect fit new element in,screw two screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sullivan, IN
- Parts Used:
- WP8053834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broke outer glass on oven door.
Repair relativley easy only needed phillips screwdriver to complete repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddie from Kaiser, MO
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the heating element went out.
removed the two screws and unhooked the old heating element. I set the new element in place and attached the electrical leads and replaced the two screws and tested the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Wooster, OH
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove kept turning off
Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from SALCHA, AK
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner control failure/unable to regulate temp.
Unplug range from 220VAC outlet. Remove screws on back of range control panel and lift cover exposing controllers and wiring. Remove burner controller mount screws. Measure old controller shaft length/new controller shaft length (per instructions). Adjust new burner controller shaft length. Remove wiring from old controller (one at a time) and place on new controller. Install new controller and secure with 2ea mount screws. Re-assemble cover/control panel. Plug range into 220VAC outlet. Have wife ops check....everyone's happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph R. from Candia, NH
- Parts Used:
- WP3148952
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not heating properly.
Removed rear panel and removed switch. I placed wires from old switch to the new one. re installed switch an back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Cornelius, NC
- Parts Used:
- WPW10181986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven temperature did not stay as set
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from tonganoxie, KS
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Self Clean Would Not Function
Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Fishers, IN
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower element burned out
Went on line to see if the repair could be done by us. Watched repair video and from there on the repair went as smooth as it possibly could.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eloy from Andrews, TX
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element not working
Turn power off at breaker box, remove back cover inserted wires into element, done and ready to be use
Was this instruction helpful to you?
Thank you for voting!