79079914302 Kenmore Range - Instructions

Turn off the power to the range. Remove oven racks. Remove the two screws and slowly pull the element out being careful not to pull the wires off. Remove the two wires then attach them to the new element. Push the element back in place, put the screws back in, turn on the power and turn on oven to make sure the problem is fixed

1.Take no chances. Turn off power at main breaker box (Range). 2 2. 2. 2.Remove inside grills then pull damaged element forward to expose wires and screws. 3. Use nut driver or phillips screwdriver to undo both screws. 4. Remove burnt out element then replace it new one. Make sure both sides are firmly pushed onto the wire terminals before tightening screws. Replace grills. close oven door then turn breaker at breaker box on again.

Disconnected the main electrical plug from the wall for the oven..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..

i removed the back panel removed two screws pulled the element out

Unplugged oven, pulled out old element, reattached new one, making sure to be careful with wires, and put on as secure as possible, just like it was before. . . Very easy to fix

Removed screws. Tried to pull out old element but spade lugs on old element were bent at ninety degree angle. Once I figured that out I was able to manouver the old element out with the attached wires. Had to be carfull that the loose wires did not slip back ijn through the hole. Reaching in over the oven door was a but diffcult, but all-in-all the jobe was done in a few minutes.

My husband had recently moved out of our house so I was very nervous about trying this repair myself but it was actually very easy!!I ordered the part on Monday, it arrived on Wednesday and Wednesday night I was baking dinner in the oven!!

My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!

slid the old one out and slid the new one in.turned the unit on and it works

Very simple, 2 screws, replace element, put screws back into place. The BEST thing... ordered on Tuesday afternoon, received on Wednesday afternoon, and Thursday was New Years day. This has been the best service, from any parts company, that I have ever ordered from. Keep up the good work!

I removed the 2 screws, making sure not to drop the wires attached. Took off old wires ,then put new wires on new element, screwed it back into place and it was working. sooooo easy!!

i called Sears and ordered the element and they charged me 16.99 plus the part to ship the next day. after 1 week i called them and they said the part was on backorder. i then check with them each week almost a month and the part was still on back order, I asked if they could fix it faster if they came to the house, they informed me it would cost 65.00 for a repair person to see what part i needed and after that they would schedule m e for a repair when the part came in. meanwhile i could not use my oven. i happened to go on line and came up with your web site. i ordered the part and 2 days later my son installed it. my oven works great . your company is awsome.

The directions have been stated many time and they are quite simple. Take out the two screws, pull the element so the wire connections come through into the oven. Disconnect the element at the wire connectors and replace. This is a dirt easy job.

The only real area for a potential problem is pulling the wire connectors through into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.

Watch the easy install video a couple of times and easy as a piece of cake!

Unscrewed 2 screws, pulled the wires out and unplugged the old element, plugged the new one in, screwed 2 screws back in, so easy anyone can do this, it's nice to have a second person holding a flashlight but couldn't be any easier.