Models > 9117858310 > Instructions

9117858310 Kenmore Range - Instructions

Jump to:

All Instructions for the 9117858310
106 - 120 of 230
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
karen from Chicago, IL
Parts Used:
WB2X9154
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
oven without heat
Took off the 2 bottom covers, saw the igniter did'nt glow, checked for voltage,yes.Ordered part. when had part,pulled out ignitor,respliced wires, and did in reverse order.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Las Vegas, NV
Parts Used:
WB2X9154
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
ovens ignitor went out as they so often do...
I first checked the power by pushing oven button, I heard the relay make a sound " CLICK" ,I then knew it wasnt the power .I then removed the oven racks and then I removed the the two screws holding the pan in place. I hit the power button and noticed the ignitor did not glow as it should.I ordered the part and replaced it and had frozen pizza 20 minutes later.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Greg from Yuma, AZ
Parts Used:
WB2X9154
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Old igniter failed
Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas from LaMoille, IL
Parts Used:
WB2X9154
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
oven would not start,
removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Mentor, OH
Parts Used:
WB2X9154
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Gas Oven would not lite - broiler and top burners operate
The stories posted on your web page are great - only improvement would to add a schematic of the parts being removed - no issues were encountered - great service by the way - part arrived the next day - a Saturday!

John M.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chad from Hanford, CA
Parts Used:
WB2X9154
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
oven would not light.
simple remove & replace. 2 min job. Couldn't be happier.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Las Vegas, NV
Parts Used:
WB2X9154
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Socket set
The oven would not ignite
I took the old igniter out and replaced it with a new one.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
william from chicopee, MA
Parts Used:
WB2X9154
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Wires On The Stove Were Short.
Removed the back part of the stove to reveal the wires connected to the igniter. Removed the wire nuts and removed the igniter. Reused the old bracket to mount the new part. Attached the wire nuts and replaced the back parts of the stove. Worked like a charm.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
gerald from South San Francisco, CA
Parts Used:
WB2X9154
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set, Wrench (Adjustable)
I would turn oven on and it show 100 but would not light.
To diagnos i removed the lower tray and could see the ignitor was not lighting like the broiler was,the same ignitor.I had the same problem as some of the other people so that was helpful.I removed bottom storage tray and could get to the wires and it was an easy fix,took about 40 minutes total.This website was very helpful also with excellent service on the parts and i saved a bunch of money!
Thanks,Gerald
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Otsego, MI
Parts Used:
WB2X9154
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set
The oven igniter on our GE oven failed to ignite and the oven refused to work.
First I got on line to make sure I had the right part. After it was delivered I started the project by unplugging the stove! A magnetic end for your socket device is very helpful.:-)A good alternative light source is esential to see what's going on.There is no need to pull out the stove.I then took off the oven door which is an easy process(Pull up off the hinges). I also removed the oven grates and lifted out the bottom plate which included the heat defuser.I then took out the storage drawer. The next step was to remove the rear screw and front 2 screws holding the burner tube. Then it was just a matter of pulling up on the tube and removing the screws holding the igniter.The 2 wires were then cut and the new igniter wires were spliced in with the new wire nuts that came with the package. I also used a little electrical tape to hold things in place. Then it was just a matter of replacing everything in reverse and plugging the stove back in. Everything works fine.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Show Low, AZ
Parts Used:
WB2X9154
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench set
gas oven electric igniter
1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephen from Randolph, NJ
Parts Used:
WB2X9154
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Oven Would Not Light
Removed the bottom cover plate and the bottom storage drawer. Disconnected the burner and removed it. Replaced the old igniter with the new one. The new one required the wire connectors from the old one to be spliced onto it. Reattached the ignitor to the burner and reinstalled the burner. Tested the new ignitor before reinstalling the cover plate and storage drawer.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nicholas from Palmyra, NY
Parts Used:
WB2X9154
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
Sunday night 4 days before thanksgiving oven wont light
Part arrived day before thanksgiving bent old igniter back and forth till broke off then easily took out screws.Cut and strip old wire, screw on new ignighter this was tough to get a wrench on with the positioning but after connecting those wires and slappin the rest of the oven back together one turn of the temp knob told me thanksgiving was going to happen Thanks to part select I was lookin like a hero!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Glen from Medford, MA
Parts Used:
WB2X9154
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
lower igniter dead
With directions from the website as well as in the box, the repair was almost flawless. I needed to be a mouse with a 6mm box-end wrench.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from lebanon, PA
Parts Used:
WB2X9154
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven refused to light checked all connections suspected the igniter was bad
Removed bottom drawer removed door and racks and bottom shield.disconected two leads from igniter . then struggled to remove igniter. after ordering part readf comments from other men and the man who said he removed the burner hit it right on the head after the part arrived the very next day after ordering it i removed the burner attached pig tails and had part installed and stove back together in 15 minutes. thanks good experience
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 9117858310
106 - 120 of 230