9113638811 Kenmore Range - Instructions

Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.

After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge came through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!

First I removed the oven door from the support hinges. Next I pulled the bottom pan drawer out to get to the tension spring. I released the tension from the hinge, unscrewed three screws that held the hinge in place. From there I replaced the hinge put all components back in place and did it all under 20 mins. The part was received with in 3 days from PartSelect so I was very satisisfied with the service and ease of repair.

After reading other stories, I knew enough to slide the lower drawer out and take off the spring. 30 second job. I did not realize that range doors slide vertically off the hinge, did that in about 2 mins. Put the new hinge on in 2 mins (3 Screws). Slid the door back on and done. Works like a champ. My wife has her eye on new stainless appliances. Sadly, she'll have to wait a while longer.

Removed the oven door. Released spring on hinge. Removed 3 screws. Removed broken hinge and replaced new hinge reversing these steps.

The left door hinge was broken. There are three screws that hold the hinge. It is very easy to take it out and put the replacement in

Slid door off hinges. Removed 3 screws which hold hinge in place. Removed drawer to access spring for hinge. Gasped at all the crumbs and crap which had collected underneath the drawer. Cleaned up crumbs+crap from floor. Disconnected spring from hinge and removed old hinge completely. Installed new hinge with 3 screws. Attached spring to hinge - center hole fitting. Slid drawer back in place. Angled hinges outward in order to re-install door. Slid door back onto hinges. Door now operates nice and smoothly. Job well done.

Pulled oven door up and off. Removed old hinge and installed new hinge. Replaced oven door. It was a very simple job. The whole project took less than 15 minutes.

I removed the door by pulling it up (according to the instructions). Than took a philips screwdriver and
removed the three screws in each hinge, unhooked the springs
and slid the old hinges out of the slots.
The new hinges slid into the slots perfectly so the screws
were installed, the springs rehooked and the door installed.
Real simple.

Pulled the three screws off unhooked the spring then removed the hinge. attached the the new hinge to the spring put the screws back in slid door back on took less than 15 minutes.

I really can't add much more to the very good instructions already posted. You will need a flashlight to see the spring -- when connected it stands vertical with one end connected to the hinge. There are 3 holes you can connect to -- I used the middle one, #2. The other end of the spring is anchored to a hole/slot in the stove frame. It is very easy to position this spring. Be careful though, there's a lot of sharp sheet metal in there. You will need a phillips head screwdriver to remove/install 3 sheet metal screws that fasten the hinge to the stove.

The plastic wheel glide that the hinge runs back and forth on was worn off on one side so it was grinding and binding.
Remove storage drawer from under oven. Open the door to the special catch position and carefully lift door off the hinges - (not by the handle, hold onto both sides).
Take out three screws w/ a hex head nut driver, slip the hinge down into the hole, look under drawer area w/ flashlight and carefully unhook spring, while holding onto spring- pull old hinge out, see which hole has wear (that's the one you want to use of the three), insert new hinge all the way in and hook up spring. Pull hinge out and line up front plate w/ holes, insert 3 screws snugly. Done, awesome probably saved a 200.00 visit from the appliance guy. My husband thinks I'm amazing!

I removed the door by pulling up and away from the hinges. I then removed the drawer. I unhooked the tension spring by hand and noted the opening. I then removed the three screws on the hinge assembly, removed the ole part, and replaced it with the new one. I replaced the tension spring and slid the door back on to the hinges. I did it all in less than 10 minutes.

I unscrewed the broken hinge, removed the tension spring and replaced the old hinge with the new one. total time 5 mins works great.

Following the repair video made the job very easy and quick, about a 5 minute repair. Wife says oven door never worked better. Thanks a lot for all your help.