9119179181 Kenmore Range - Instructions

First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and reconnecting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.

1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two retaining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake

Easy

The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best

I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. I then secured the new unit to the oven wall with the two screws.

1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace of tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.

4 screws held the cook top down, took top off exposing the burner elements, ordered the one that was bad ( could not
believe how easy it was to order from Partselect, and then how quick I received it.) Shocked myself when taking out the element, forgot to disconnect the breaker.

Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!

This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices!
Thank you,

Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & since I was so tired from all of this 5-minute activity, I rested.

Al S.

After reading other stories, I knew enough to slide the lower drawer out and take off the spring. 30 second job. I did not realize that range doors slide vertically off the hinge, did that in about 2 mins. Put the new hinge on in 2 mins (3 Screws). Slid the door back on and done. Works like a champ. My wife has her eye on new stainless appliances. Sadly, she'll have to wait a while longer.

just plugged in the two prings into burner into outlet. Very simple and quick.

First I removed the oven door from the support hinges. Next I pulled the bottom pan drawer out to get to the tension spring. I released the tension from the hinge, unscrewed three screws that held the hinge in place. From there I replaced the hinge put all components back in place and did it all under 20 mins. The part was received with in 3 days from PartSelect so I was very satisisfied with the service and ease of repair.

This is how I did it--but I would strongly recommend you do step 4 first, and skip step 3! Remember, because 240V circuits have 2 "hot" wires, they may be "hot" (120V to ground) even when switched off!

1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.

Removed the oven door. Released spring on hinge. Removed 3 screws. Removed broken hinge and replaced new hinge reversing these steps.

I watched the video on the website then installed the part. In fact, I watched the video twice because I could not believe it was that easy. You can not do any better than PartSelect. Shipping is fast and the instructions are great. If I ever need a part for any appliance I will go to PartSelect.com first. Keep up the great work and thank-you so much!