2783218510 Kenmore Range - Instructions

Basically followed the instructions that others had posted. Removed the bad oven igniter by removing the two screws securing it to the burner. Attached the new ignitor and then spliced the new wires into the old wires with the ceramic nuts that came with new igniter.

i removed the oven door and then the lower panel.the two screws holding the igniter were hard to access, so i removed the gas rail.this made the job much easier. the advice from other people on this website was very helpful and made the repair much easier.just remember to shutoff both the electric and gas supply.

I removed the oven racks and the bottom cover. The bottom cover had 2 hand tight screws. Then I had to remove the silver sheet metal plate attached with 1 screw. Then I removed the 2 small screws that held the old Igniter in place. Then removed the 2 wire nuts connected to the oven wires. The new igniter fit in the same place as the old and I attached it using the same old screws. Then I connected the wires using the new wire nuts provided in the igniter kit. After testing the new igniter by turning the oven on to 200F, i replaced all the parts i removed including the silver plate the oven bottom and the racks.

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my plan :)

This site provides excellent instructions and saved a lot of time and effort.

Replacing the part only requires basic skills and attention to detail. The kit I received included ceramic wire nuts to splice the new igniter to the old connections. Be sure to leave enough wire to mke the connections properly.

I first read and printed out several postings on how others did the job. I read and re-read them and then I started. I cut power to stove and left gas on. I removed door, pushed back and removed bottom burner cover. I exposed the igniter which I deduced was the problem. I removed the front burner screw and the rear screws (2) and the burner came out very easy. I removed the igniter from the burner, made sure which wire went where (I marked them)an snipped them. I used the ceramic caps and spliced the wires. I replaced the burner and turned on the power. I turned the oven knob on and "Viola", the igniter came on and burner came to life. I replaced every thing in reverse order and called it "done". It was so easy with the postings on this subject.

1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy

frist tested ignitor with meter removed ignitor order
part , I recieved to my surprise next day I'm a very happy person

The biggest problem is to get down low enough and far enough back to be able to reach the igniter. Other tan that , it was a simple affair.Unscrew the old one and detach the wire nuts and reverse the procedure for the installation and hope the gas valve has'nt been affected

1) use screwdriver to remove screws securing lower pan in oven (screws are at back of oven)
2) remove lower pain to expose igniter and burner
3) remove lower storage drawer
4) disconnect 2 igniter wires from where they are attached underneath
5) use nutdriver to remove burner from above and below (this makes it easier to remove the igniter)
6) use nutdriver to remove the faulty igniter
7) cut off clips from faulty igniter leaving enough length to strip and then attach with ceramic caps to new igniter. (be sure you attach the right clip to the right wire)
8) reverse the process to install the new igniter.
20 minutes tops

Removed bottom drawer removed door and racks and bottom shield.disconected two leads from igniter . then struggled to remove igniter. after ordering part readf comments from other men and the man who said he removed the burner hit it right on the head after the part arrived the very next day after ordering it i removed the burner attached pig tails and had part installed and stove back together in 15 minutes. thanks good experience

The range still worked and the broiler still worked. I noticed that the ignitor for the broiler turned on and glowed a short time after starting the broiler. I dissembled the floor of the oven (just two screws) and tried the same for the oven, but the ignitor did not start or glow. I ordered the part. It was sent withing two days. It was easy to replace and the oven has worked well since. I recommend ordering the attachment fixture as well, in that taking apart the one that held the old ignitor immediately stripped a screw and I ended up bending the fixture and having to reshape it (the small extra cost will be very well worthwhile!)

Removed the three screws from the top and bottom of the oven door. Removed the outside door cover from the inside door panel. This gave me access to the six screws that hold the two sections of the inside panel together. The glass of the inside oven window was manufactured without the installation of retainers to keep the window from moving. I installed the four retainers that I purchased. Reassembled the door. The glass now stays in place. Since there were no retainers to begin with I had to figure out how they were to be installed to prevent the glass from moving around.

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstalled protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.