91136655793 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Herbert from Tallmadge, OH
- Parts Used:
- WB14X103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
hinge roller was worn out
Very,very easy. Just like the video described. Removed three screws. Released the spring and removed the old hinge from the slot. Slipped the new hinge in the slot,replaced the screws and reattached the spring. Job done! Great service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Lorain, OH
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
only back burnners lit
Rremoved the back cover, changed the wires from one ignighter to the other, removed the old ignighter, and snapped in the new one, put four screws back on cover, and pushed stove back into place, turned on all burners several times to make shure eveything worked!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Lake Stevens, WA
- Parts Used:
- WB14X104
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven door wouldn't open without serious assistance
1. Google your appliance problem. 2. Watch whatever YouTube videos that are available. 3. Follow the excellent instruction provided by PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Coal Creek, CO
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The range kept giving an F2 alarm
When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.
Was this instruction helpful to you?
Thank you for voting!
change over from natural to lp gas
i removed the cover over hole that holds the orifice used a 7mm nut driver with butyl rubber tape stuffed inside nut driver, this stuff is sticky and holds orifice in place while positioning over hole.total time about 3 minutes. they worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
Oven door difficult to open, would only open 4-5 inches
Followed the video step by step, made the job simple and easy. Did not know there were springs attached to the lower part of hinge till watching video. Parts were genuine GE manufacturer parts which fit perfectly. Very helpful staff and great customer service. My model number did not match perfectly with others listed but the hinge part is identical.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- delbert from Auburn, WA
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door hard to open and close
Pull the door off the hinges. pull drawer out of range.Take sping off both frame and hinge arm. Unscrew three screws holing hinge in palce. pull old hinge out , put new hinge in . reinstall screws, spring, drawer , and door. Get the wife to make cookies.
Was this instruction helpful to you?
Thank you for voting!
Oven door wouldn't open/close properly; hinges offset & wheels broken
Followed YouTube video from PartsSelect. It was real easy to do and that video was helpful. Took off door by sliding it up off hinges, disconnected springs, unscrewed hinges & slid them out - reversed to install. Worked perfect, parts were exactly right and parts came within 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Grass Valley, CA
- Parts Used:
- WB2X9146
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer guide
Used Phillips screw driver, installed guide, applied lubricant.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Arlington, MA
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Left side front and back burner would not light
I located the spark module at back of top panel and I switched the wires of one of the other burners to the burner that wasn't lighting. By doing that I found that part of the module wasn't operating properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Las Vegas, NV
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner Spark Module burned out needed a replacement
My husband did the repair so it was very easy for me, as well as for him, he found the bad part from your parts diagram which was a great help, he changed it out in no time and so we were both very Happy. Thank you for your help. Nancy & David
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Waukesha, WI
- Parts Used:
- WB2X9146
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drawer coming out of the track and falling to the floor.
pulled drawer out and installed drawer guide
Was this instruction helpful to you?
Thank you for voting!
door won't open all the way
replaced both hinges in no time flat and it was easy to find the part and instructions on parts select. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from bristol, CT
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Door would not open all the way
Well after fighting with the door for a month, i went on this site and using their information, i found the model number (in the process i found the receipt for the oven and found out it was 20 years old still looks and works like new. Pulled the door up and off the hinges, removed the drawer, saw the spring was in the middle hole, removed three screws pulled out old hinge. Installed new hinge, 3 screws and the spring. put the door back on and wow it worked! Thanks!
Was this instruction helpful to you?
Thank you for voting!